Hello Agilent Community Our Zero Air / Nitrogen generator from Parker Balston broke down and it has been discontinued. The supplier does not offer replacement parts and they do not longer have a gas generator model with the combination Air/Nitrogen. Therefore…
Hi!
I've got a SEQ type CC that should be calculated only once during the reprocessing and a peak or group type that uses the result of the SEQ one. Since this the SEQ type CC is calculated inj number * peak number times.... is it possible to avoid…
Hello.
I'm hoping to seek some help for a problem I've been experiencing. We currently run a GC-FID with a headspace sampler testing for Acetic Acid, Propionic Acid, and Butyric Acid. I've been having issues reading the acetic acid consistently. Any…
Larger are the orifices of the cones, particularly the sample cone, more chance you have to get the IF/Bk pressure errors. Usually when the sample cone is too used then is passing too much air or whatever trough it at the interface, and the ICP senses…
I'm a new GC/MS user and I have the following error: Inlet: Pressure Pre Shutdown warning after changing the column of a Intuvo 9000 Device. The total flow target of 4mL +/-2mL/min fails and the leak rate doesnt' reach values below 11mL/min. Can anyone…
Hi everyone!
I have brand new PGC Yokogawa 8000 equipped CP-Chirasil-Dex CB Columns with FID detector and Liquid Sample Valve (LSV) set at 170C deg. The problem is GC can’t separate m-Xylene from p-Xylene in low concentrations.
Component name…
Hi Crystalnipp (great username!!) Thanks for the clear answer I do have a question for you. We also run N2 make-up to our FID. As of now we run He and our night standby method is to leave the GC oven at 150°C with 0.5mL/mim He flow. We turn flame and…
Hi acraig First replace saptum until if you don't detected leak because sometime tiny leak in saptum cause low sensitivity. Second sometimes over tightening the ferrule connection of column to injector cause constriction the flow and reduce analyte at…
Hello,
I have inherited a 5975 MSD and when I go to autotune, there are no peaks present and the tune fails. I get alternating errors "Gain and Offset = 0 and peaks are too narrow" or "Tune action stopped: The valid Range for Ent Lens Offset is 0…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...