I have a Cary 3500 and running Cary UV Workstation Software 1.2 and Windows 10
I downloaded the new Cary UV Workstation Software 1.3 via the Agilent SubscribeNet.
first I ran the systemPreparationTool.exe
That finished without issues.
Then I ran…
hi community we are developing a method on short chain fatty acids in plasma sample, using a DB fatwax UI column on GC-FID. we are using diethyl ether as extraction solvent however our recovery of patient samples are not so good and looking to use Isoproponol…
Good morning,
We have an autosampler (Agilent G4567A) for our GC-FID (7820A) and the following method for cleaning and injecting samples.
I have noticed that when the syringe pumps 2µL of sample for cleaning, it then pumps quite a large volume of…
Hi, I know this is an old thread, but I am having a very similar issue. I am wondering how did you know to replace the interconnect spring rod? How did you know this was the issue, and that it was not instead an issue with the FID board or the electrometer…
I have a 6890N GC with an MSD and a GC that I am trying to qualify. The MSD works fine but when it comes to the FID the units are showing as mAU and not PA so it will not pass the validation test. Does anyone have any idea on how we can change the units…
I have a 6890N GC with dual FID. The back column has a much higher flow rate than the front column. The two columns are identical and the setup for inlet, column and detector are identical. I have also swapped the EPC's between the two detectors. Seems…
Hello. We have a 2- dimension gc/fid/ms 8890/5977C with a masshunter software. Our aim is to quantify molecular markers (e.g. 1,3,5-Tri-tert - Butylbenzene) used in gasoil to trace fraud. For quantitation we use a sim method (Quantification sim 231 and…
We don't know what is in your water samples, but on a CP-Wax 57 CB benzene and isopropanol are eluting very close to ethanol, just in front of it.
You can find examples of applications of alcoholic beverages on Wax 57 (all types) in Scanview ( (+) Software…
Hello mckenzie.stevens ,
Did this error occur when attempting to work with the FID data? I've not seen this exact error, but it is possible to receive similar errors when having a spectrum tool selected and trying to work with non-MS data. If you then…
Hi,
After a power cut, the batch file I had open on my desktop seems to have become damaged...
On opening the batch, it fails to open... small dialogue pops up >> "failed to open quick scan file. Failed to read binary quick scan file."
Has anyone…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...