It all depends on your following steps. You can even use Methanol or Acetonitrile for the protein precipition: Protein Precipitation for Biological Fluid Samples Using Captiva EMR-Lipid
See also the chapter on protein precipitation in Agilent's Handbook…
The Digest of upcoming webinars has been updated as of April 30.
Did you miss April's GC Live Session Recording and Discussion Thread? Check it out here: ( +) Diagnostics From Your Desk, Troubleshooting From Your Kitchen Table - Follow-up Discussion…
Hello cjwwfd ,
B.06.00 is out of support at this point, but I can offer some general suggestions for current revisions and hopefully you can apply them to your version. Version 12.0 is the current release. If possible, I would investigate your options…
I'm experimenting the same error. Logbook displays <MSQQQ_1: QqQ fault detected: 1.23 vacuum system is not ready. This is typical during a pump down cycle or when the high vacuum pump is turned off during a vent cycle or fault condition>. Does anyone…
Hello DET ,
Sorry for the late response on this.
What sort of spiking do you see usually? What is the output of the FID, in pA?
Are you using any UPS systems, or are the GCs plugged directly into the wall?
Hi, I think it would be a good idea to upload your startup tune report in order to help you better.
Also I think you could take advantage of reading this post: https://community.agilent.com/technical/atomic-spec/f/forum/470/icp-ms-manual-tuning
Hello,
So, file based workstations store the full path to the methods in the sequences. If there is any change between the systems in the project path this is the expected behavior if you copy a sequence. If you open the sequence, browse out and find…
Hello guys,
I recently discovered, that it is possible to change your font properties in the injection list via shortcut (ctrl + b for "bold" and so on..).
Therefore I wanted to ask you, if there is some code for changing font types for CCF outputs…
Hi Mai,
Thank you for reaching out to Agilent technical support.
Please check:
if the data file you are trying to open was generated using TapeStation security module as that can be one reason for the file not to open and error out.
If anyone…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...