Hi, I have a agilent GC 7890B with FID. currently i am a facing a problem regarding this GC, problem is like that - all gases supply is ok, no leakage is found in detector portion. i have cleaned the FID & Jet but flame is not burning. So kindly suggest…
Hi John, You are on the right track-- it sounds like your flame is not lit. The reading you are seeing on the Hydrogen line is likely back-pressure from the column flow. That result could indicate a blockage in the jet, but the flow is a little low to…
good day!
tell my please..
I have the air generator and his out pressure consist 52 psi, and and air consumption is 1000 ml/min. the EPC module GC 7890b work in rang 55-80psi. I have 2 detector FID. Tell my - with this generatorom may be worked ?…
Hello, im having a problem with a 2d GC using the Deans Switch system. Its a 8890 GC with 2 FIDs. The problem is that, when cutting peaks from the 1st dimension to the 2nd dimension (2nd column), all peaks on the 2nd dimensions get split into 2 peaks…
Hi, I'm working with a LC Infinity Lab 1260, which has a standard autosampler and 100 uL loop. I'm trying to achieve a very simple injection program, but keep failing. All I want to do is to draw 50 uL from a sample vial, 50 uL from a second sample vial…
Hi all,
I'm using a 0.18 mm HP-5 GC Column on a Shimadzu GC-2014 connected with a FID. I'm looking to get new ferrules (the old ones had been passed down from previous users) and wanted to discuss some options. I tried using some 0.5 mm graphite ferrules…
Hello, Software used: - MassHunter Workstation Version 10.1.49 - MassHunter Qualitative Analysis Version 10.0 - MSD Chemstation Data Analysis (can't figure out version, when I click the help button error message "failed to launch help" appears) I am having…
External Device not ready. Is it an Agilent Autosampler? Which model? Do you have another device like a headspace sampler?
APG Remote. There is a cable between the GC and the MSD so that they both start at the same time. A remote start cable from another…
Hi all,
I am having a recurring issue throughtout my sequences. When I check the sequence log after a run, where I place a masscal between each sample, I see in the sequence log the following error:
5) MassCal: ' ' Starting QTOF MassCal: Mon Nov…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...