I was experiencing ghost peaks in my water blank shots so I decided to do some maintenance. This included a new S/SL liner and septum, removing the first inch or two of the column, FID disassembly and ultrasonic cleaning of the jet, and reassembly. Now…
I have a problem with my FID on a HP-4890d Gas Cromatograph.
The FID was working as normal, then the FID didn't start, so I checked the gas flows, and the H2 didn't come out from FID.
I suspect maybe the Hydrogen pipe line is clogged or the on/off…
I'm trying to install MSD Chemstation(G1701-60160, E.02.02), but error code below poped up and failed to intall it.
-I use VDI at my work place
-Its version Window10
SetupNew|setup.cpp(140)
PAPP:
PVENDOR:
PGUID
|15.0.0.498
@Windows Vista…
Hello hoh ,
I have not seen this error specifically, though this part of the message points to some issue with the chemical structure -
System.ApplicationException: Failed to get chemical structure for CAS = 1000331265; structure database may be corrupted…
Hello everyone,
7900 extinguishes plasma when trying to perform Auto RF matching in any mode. Error code: Plasma was shutoff during Analysis (Vacuum), Warning code 2150: Interface Vacuum is too low. Plasma ignition is well. Orifices are in good condition…
Hi Guys, I have a 7980B GC with an external injection valve and FID detector. I am using OpenLab CDS Chemstation Version C.01.09 with Windows 10 (version 1703). Sometimes while running a sequence it fails to save the chromatogram. When you select the…
Hello ajay_zalavadia , Thanks for sharing your question in the Forum. When you look at the JSON responses where deserialization fails, compared to the responses where it succeeds, are you able to spot exactly what is the inconsistency/differences in the…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...