What should you consider when selecting gases for your new GC or GC/MS system?
Which gases will you be using?
Did you c onfirm that gases available are a supported configuration for installation ?
Gas requirements are specified in Site Preparation…
Hello, I am running residual solvent testing on a product for my company and I am having issues with peak sensitivity. I am running this testing on a 7890/7697 GCHS-FID combo. I am tasked with coming up with a solution to this issue by only adjusting…
Hi Paul, thank you for your reply. I can't attach a full autotune report due to it failing mid run. I can however add the text file it generated.
Fullscreen
Autotune_20230419_130648.txt
Download
----------------------------------…
I have proposed system from agilent 7890B to check high purity gases . system consists of TCD , PDHID and FID . me question is do you think that system is complicated and i have risk that if any fault happened the whole system will be down . How to guard…
Hello! My multisampler (G7167B: DEBAR00250) has the following error: compressor has error EE 30756,0. According to the manual, this indicates a possible hardware error. I ran a sample cooler function test, which failed, and the result comment is: target…
Dear colleagues
We have Agilent LCMSD 1260 Infenity /6130Quaderpole. we encountered this error: Install module C:\Chem32\CORE\HPSCIL00.DLL, failed
We want to know the cause and the solution for this error ?
Thanks in advance.
With my best regards…
We are running long term tests with multiple GC analysis, automatically controlled from LabVIEW via ActiveX communication with OpenLab EZChrom. We recently had an event in the EZChrom software creating problems; suddenly midway through the tests, the…
Dear Community
I am using a GC/FID from Agilent with Openlab CDS. The GC/FID has to columns (front and back) which gives a slightly different retention time for the same substance. I use both lines, one for the measurement and the other for the control…
I don't think it would have a problem as long as you're not trying to connect with both software platforms at the same time. I've seen other customers do similar things (GCMS/FID, using MSD Chemstation for MSD work and GC Chemstation for FID work).
Good afternoon all. I have a baffling issue with our 6470 LCMS. It passes checktune. I can run autotune is positive mode or in negative mode, but not both together as previously. I get an error message at the end of the autotune process stating "Failed…
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The following procedure is to learn how to use the tools in the Compound Information window to view chromatograms and spectra for your data.
Steps to follow...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Batch Table can be configured with many different data columns. This article uses an existing demonstration batch with method and analyzed data files to view different...
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...