Hi All,
I am experiencing a configuration issue with a new Thermo Fluorescence Detector installation on a 1200 series LC with OpenLab CDS 2.5. After installing the SII 1.2 Software for the FLD, I try to configure the FLD with Chromeleon, however I am…
Slightly related: As part of a new lab setup, I decided I could greatly save having to replace cylinders if I ran my FID on a one-fifth flow of pure oxygen instead of compressed air.... Maybe you could guess the result. Every ignition was a detonation…
Your controller is going in Auto Tune
Autotuning condition is shown when the controller has delivered an output power level higher than a typical value, but the pump is still not reaching full speed value.
It does not matter if it is a normal start…
User could not tune and was getting missing .xml errors. This error was observed in MassHunter Acquisition software B.07.00 on a GC QQQ but may be relevant in other revisions as well. Error in auto tuning! Missing XML file or invalid contents. Failed…
Hello! I followed this tutorial part D Linked Dual GC Signals 1 aliquot /cfs-file/__key/communityserver-discussions-components-files/152/0020.DualTow7890EnvMH.pdf to sample 1 aliquot through both the front and back autosamplers, both columns, to both…
It is a capillary, USP 401 The gas chromatograph is equipped with a flame-ionization detector, maintained at a temperature of about 260°, a splitless injection system, and a 0.53-mm × 30-m fused-silica capillary column bonded with a 1.0-µm layer of phase…
I got a data sheet for my Agilent 7890 FID detector. The stated linear range is 10x7. This range I think should mean that from 1% down to 0.1 ppM the detector is linear for Tridecane. I figure concentration-wise in splitless mode - that works out to be…
Hello, We are using Agilent 7890B GC/FID with Headspace sampler. There is a problem in FID unit of the system. In FID parameters, Temp is 220 C, H2 fuel flow is 30 mL/min, Makeup flow (N2) is 25 mL/min, He flow 1 mL/min. These are setpoints and actuals…
Hello howard_sanford ,
I tried clearing the preferences for IDBrowser, and it did work when I used the old PCDL, but the "m/z" column in ID Browser did not show anything. So, I did it again and for the second time, the m/z of features showed up, but…
In my experience, usually when a method fails to download to a 7820A GC it means that one of the zones on the GC is in a faulted state. This does not always get reported in the instrument actuals in ChemStation, so the best way to double-check this is…
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...
This Information Applies To: Agilent OpenLab CDS Software (ver 2.x).
Issue:
This article will give instructions on how to submit a single sample run in the OpenLab CDS Software.
Steps to follow:
Launch the acquisition software through the...
This Information Applies To: Agilent OpenLab CDS products
Issue:
Every computer running Agilent OpenLab CDS Software requires a unique software license for continuous operation. Failure to install a valid license will cause the instrument control...