Instability in the anode voltage will cause baseline problems in your detector signal. For example, if the lamp doesn't light properly, the voltage will reset and you will see periodic changes in the baseline. I have seen old lamps sometimes produce odd…
I can't seem to get our new instrument to pass an EPA DFTPP tune for method 525.2. We recently got an instrument with the hydroinert source and I have only gotten a couple of passing tunes but nothing that is repeatable. I have tried manual tuning myself…
Yes! I checked the line too as according to the instructions (+) How to Disassemble and Assemble the HES (High Efficiency Source) - Articles - GC/MS Portal - Agilent Community
I will take a picture when I have them out next time. Thank you so much for…
Analyze Agilent Seahorse XF Real-Time ATP rate assay data using Agilent Seahorse Analytics
Analyze Agilent Seahorse XF Hu T Cell Activation Assay data using Agilent Seahorse Analytics software
Analyze Agilent Seahorse XF Substrate Oxidation Stress…
Hello APacana ,
The reason for the difference in response between the TIC and the EIC is because when you extract the TIC of a given precursor you are extracting the ion signal from all precursors that create a 72 product ion, using your example. If…
Hello AJohnson13 ,
Here is the PC setup guide for older Windows 10 versions of MassHunter. It includes the PC specifications.
Windows10_Setup.book (agilent.com)
The software installation instructions would be included as part of your original media…
At 1 mL/min pumping water, the pressures are as follows:
Pump + Column = 53 bar
Pump + Column + 0.1 mm ID 30 cm tubing = 70 bar
Pump + Column + Tubing + Flow Cell = 75 bar
I have also confirmed that this pressure fluctuation has nothing to do…
It all depends on your following steps. You can even use Methanol or Acetonitrile for the protein precipition: Protein Precipitation for Biological Fluid Samples Using Captiva EMR-Lipid
See also the chapter on protein precipitation in Agilent's Handbook…
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue:
The Flame Ionization Detector (FID) jet could become clogged with ferrule material, column bleed, or heavy molecular analytes. The clogged jet will affect...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different high concentration, split analysis techniques including:
General use liners
Auto inject, general use
Auto...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different splitless trace analysis techniques including:
General use liners
Pressure, temperature, volume (PTV)
Hot...
This Information Applies To: Agilent 6890, 7890, 7820, 8890 and 8860 GC Systems with Split/Splitless (S/SL) inlet
Issue
Replacement of the Gold Seal is required as part of inlet maintenance. Replacement is required when the performance of the inlet...
This Information Applies To: Agilent GC Systems with Micro-ECD.
Issue
The Wipe Test is an annual test that performed by end user of the micro-ECD (Micro Electron Capture Detector or uECD) to help ensure radioactive safety when using the detector...
This Information Applies To: Agilent GC Systems with thermal conductivity detector (TCD)
Issue
Baking the thermal conductivity detector (TCD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items...
This Information Applies To: Agilent GC Systems with flame ionization detector (FID)
Issue
Baking out the flame ionization detector at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items required...
This Information Applies To: Micro Electron Capture Detector (uECD)
Issue
Baking the micro electron capture detector (µECD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Warning ...
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue
This article will describe how an operator can configure the makeup gas on both the instrument keypad and the software driver (Method Editor).
Background...
This Information Applies To: Agilent HPLC systems
Issue
The presence of ghost peaks can be a symptom of a system contamination issue, caused by accumulation of sample and/or foreign substances in the flow path. It is critical for high sensitivity...