Hello,
Are you sure the end tip of the PLOT column ends up (and 2 mm withdrawn) inside the FID Jet?
Any problems when igniting the FID?
FID Jet could be contaminated from PLOT stationary phase particles ..
Best regards -
Lars
Here is a collection of Agilent 7890, 8860 and 8890 GC Resources. Links to user manuals, troubleshooting resources , tools and supplies on Agilent.com . Go to Collection of GC/MS Resources to view GC/MS information.
Agilent 8890 GC User Manuals
…
Our lab has an Agilent 1260 Infinity HPLC, and we are encountering an annoying issue with the desktop connected to it. The desktop sometimes shut down automatically, while the HPLC is still running the analysis. The HPLC keeps working and and the analysis…
Hello, anyone here know what happen with my icp-oes?
i got error message '' gas scp write channel" and icp-oes unable to running due plasma ignition failed, the icon plasma also blinked many times.
Thank you.
Rerey
The vials and caps are the same ones we have been using for years now; they are your standard 2mL GC/LC vials. I opened up LabAdvisor and ran the gripper test. It failed to release the vials even after re-initialization. I removed the gripper caps, wiped…
Hello,
I am new to MassHunter, so this may be a basic question or just something I'm doing wrong. I am trying to build a quantitation method for a large number of compounds we are analyzing via LCMS. I ran our calibrators with our LCMS method and have…
Hi
When FID is off means no flame.
Voltage applied during ignition and while FID OFF so ignitor also Off..
When ignitor off then voltage also off...
Hope, it's clear to you..
The Pfeiffer turbopump on my 5977C MSD will not start after shutdown; it does not exceed 5%. When I boot the MSD, the green LED on the pump controller is solid. Then when the turbo fails to reach 80%, the LED starts blinking and the MSD panel returns…
If your area is relatively stable but your amount/result is low, you have to have either altered your calibration values, failed to clear a previous calibration, or omitted a dilution factor. Are all results lower by the same factor or is it variable…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...