Hi everyone,
we wanted to clean the ion source for the first time.
The videos were unfortunetly not very helpfull. We lowered the temperature of gas and sheath gas and let it cool to 25°C, and then lowered the flow rate of the gas. if we would put…
Are you interested in GPC/SEC technology and want to deepen your knowledge? Then the following two classroom training courses at our Agilent University are just right for you.
Note: The course is in German, with English slides. The course will be held…
HPLC 2024 will be held from July 20-25 , 2024 in Denver , Colorado this year. We will host our Reach Your Summit Reception which will be held on July 23 rd from 6pm – 8pm local time at Earl’s Kitchen + Bar. At this event, you will find different areas…
Hello Ruthvn Please share some photos of your chromatograms and check for void volumes in capillary connections. Once the issue occurs, does it keep occurring for subsequent injections or do the resolution and acceptable peak shape come back in later…
Hello LCMSvsLCUV Would you be able to share more details about what you are trying to achieve please, including the instrument set up, application, analyte of interest and the column part number?
We are having a issue clearing up these valleys/dips after our peaks of interest. So far we have confirmed no leaks up to the column (pressure and leak test passed), new column, new guard column, new mobile phases, new standards, and several purges through…
Hello,
I will assume you mean you are using the backup restore tool for CDS 2.4 not the ECM XT import scheduler. If you have setup an import scheduler task to back the ECM-XT system up that would be self-referential and would not actually back anything…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...