I met same error while installing CDS 2.7 on Win 10 pro
[3F4C:3F40][2024-03-25T11:42:54]i000: >Bootstrapper - Execute progress: 87%
[0E04:1E5C][2024-03-25T11:43:14]e000: Error 0x80071501: Process returned error: 0x1501 [0E04:1E5C][2024-03-25T11:43…
I have an Agilent 7890A with a split/splitless injector and FID. The FID has been experiencing a falling baseline signal that triggers the instrument to relight the flame unless I lower the lit offset value. As it gets worse, I have to set the lit offset…
HP 5890 II not responding. After power-up, initiates "Passed Self Test" routine but stalls at that point. The oven works, and FID is ignited but the light by "Not Ready" is lit up. ChemStation program states: "GC Not Found. Check that GC is Correctly…
Hi, I am wondering if the FID detector requires nitrogen make up flow while in standby mode or is it sufficient to have the FID idle at a temperature above 100 to protect it in downtime.
Thanks.
Hi all, we have Error "1467: Option gas flow rate is out of acceptable range" when trying to ignite the plasma. But the thing is, we don't use option gas (we are running in laser ablation mode) and have nothing connected. We think it might be related…
Hello
I wish if i can find solution the this problem
I don't have access to ignite plasma because after i turn on chiller ( Temperature the peltier it ouside range -40 ± 2 )
some times take -52 C or more .... ( i notice there are not value exact…
I use a 8890 series GC with MSD, FID, TCD. Splitter from column to MSD & TCD or FID Multimode Inlet. 30m DB-5 Column. MMI 325C, FID 325C. 10 C/min ramp until 325 and hold for 15 min. 45 min run time It's 98% used for QC using TCD & MS. However there is…
Hi, Have this issue with an Agilent 6850 GC: The system performs normally during the pre-run: the oven temperature, front inlet total flow/inlet pressure and signal 1 valve values are all normal/stable. When we switch to the test method and start sample…
Additionally, the detector will not light regardless of whether the column is installed or not. I can hear an ignition happening but the detector fails to stay lit every time.
This Information Applies To: 4150 TapeStation, 4200 TapeStation
Issue
How to deal with a TapeStation Electrode Cartridge change is due warning message.
Background
The Agilent TapeStation controller software will notify users to replace the...
This Information Applies To: Agilent OpenLab CDS
Issue
Sometimes the integration result is not ideal for all injections. This article outlines the step-by-step instruction to manually integrate peaks.
Background
There are 2 ways to integrate...
This Information Applies To: Agilent OpenLab CDS , Agilent OpenLab ChemStation
Issue
Calculation of Area percent or Height percent for uncalibrated compounds in OpenLab software. If all components respond equally in the detector, then Area% and...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
How to power off the Agilent ICP-MS Foreline Pump to perform maintenance, or when fully powering off the Agilent ICP-MS System.
Background
The ICP-MS MassHunter...
This Information Applies To: Agilent ICP-MS (7500,7700,8800)
Issue
How to check the E2M18 or E2M18F foreline pump to determine if the pump needs maintenance?
Background
The oil cleanliness and oil level in the E2M18 or E2M18F foreline pump...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the foreline pump oil in the DS 402.
Background
The DS 402 oil should be replaced at least every 3 months or when the oil color indicates it needs to be changed...
This Information Applies To: Agilent 8890/8860 GC Systems
Issue
How to delete data that is stored on the GC instrument.
Steps to follow
Caution : Before deleting data from your GC, Agilent recommends extraction of data as a backup...
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...