I have an agilent GC-FID 6890 i use for TPH and PAH of soil samples yet i want to calibrate it for Oxygenates in gasoline and Aromatics don't know how to go about it
A follow up question about this, if it ever occurs again. When the instrument errored out it prevented us from even initializing the instrument properly. Is it possible to auto reference even if the unit failed to initialize correctly?
Welcome everybody,
The problem occurred after updating Openlab CDS Software 2.2 Version to 2.4 Version.
GC# 7890B With FID , and TCD Detector
OpenLab CDS Software 2.4
After installing the software version 2.4 and after a gas sample injection…
Hello,
I have a question about our GC 8860, which has been experiencing some problems since I changed the valve pressure.
Although it works well immediately after the change, if I don't use the GC for a few days, the first few runs produce larger…
Hi All, I need help to fix either baseline drifted down or change volume injection of water samples in GC/FID. Specifically, I am setting up a new GC instrument for analysis of methanol and alcohols in water samples with the following conditions: - Instrument…
Hi Everyone,
Due to random readings of my samples, i ran wavelength and photometric accuracy test. Both of them fails, do i need to replace the lamp or is it because of the wavelength drive gear?
thanks.
If you want to know what specific module is sending a Leak error, this article in the Knowledge Portal can help:
Determining which Module is Causing the Shutdown Error Due to a Leak
The "Valve command failed transport command failed" Error can have…
The optional high vacuum gauge has a cable between the gauge and the electronics. It is either disconnected or the gauge has failed.
See page 125 and 126 in the 5977B Series MSD Operating Manual for instructions on how to turn it on and off.
The…
When the tuning is done at 3200 (+) everything is fine. When I change it to tune at 1700 (+) the masses are reasonably accurate. After it gets to the third mass (620) it appears that the entire spectrum shifts by about 1.5 AMU and the tuning fails. There…
There is an SP7 switching valve on our 5110 ICP-OES The first set of triplicate aspirations of Std always ride really close to the precision limit of 2%RSD and then std#2 and Std3 are typical 0.5 or less. (ISTD Method) All of these standards are in the…
This Information Applies To: Agilent ICP-MS MassHunter Workstation 4.6 or below, and ICP-MS MassHunter Workstation 5.1 and above.
Issue
Guide for identifying the current software version your Agilent ICP-MS system is using, to see if any updates...
This Information Applies To: Agilent OpenLab ChemStation, Agilent OpenLab EZChrom, Agilent OpenLab CDS.
Issue
When users of OpenLab CDS forget their passwords, another user with the right privileges will reset their password, however, sometimes...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to temperature can cause the plasma to shut off or disable plasma ignition. While a warning message will still allow the plasma to light...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
How to view meters in ICP-MS MassHunter Software, or change what meters are selected?
Background
ICP-MS MassHunter allows up to five meters to be displayed at...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to replace the oil mist filter in the MS40+ or MS40-S?
Background
The oil mist filter in the MS40+ or MS40-S should be replaced yearly.
Warning :
...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to check the DS 402 foreline pump to determine if the pump needs maintenance.
Background
The oil cleanliness and oil level in the DS 402 foreline pump should be checked...
This Information Applies To: Agilent ICP-MS systems (7700, 7800, 7850, 7900, 8800, 8900)
Issue
After shutting down and restarting the ICP-MS, sometimes the communication between ICP-MS and PC does not automatically reconnect. It may be necessary...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the Foreline Pump Oil Mist Filter in the DS 402 foreline pump.
Background
The oil mist filter element should be replaced yearly , or when the level of oil in...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil Mist Filter and Odor Element in the E2M18 or E2M18F?
Background
The oil mist filter and odor element should be replaced yearly, or if the...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil in the E2M18 or E2M18F?
Background
The E2M18 oil should be replaced at least every three months or when the oil color indicates it needs...