Hello E_Johnson ,
I’m sorry for the delayed reply to your message.
Thank you for asking this question. Always refer to the applicable Agilent instrument safety information when performing instrument maintenance or repair ( 7890 Series GC Safety Manual…
Hi we are now using masshunter quant to process the data of gc/fid obtain by openlab cds and then using gc translator.the multiplier has already been set in the sequence table.and is there a way to obtain it from the masshunter in the batch table.so the…
Hello!! When running HPLC, I am receiving the following warning which prevents my sequences from running: "DAD method download failed for module G4212B:DEAA303287! Use Signal is not allowed to be changed during run." I am receiving this warning when I…
Hi, i want to update the Firmware of an 5975C with the Firmware Update program msupdate.exe of OpenLab to Version 7.02.29. At the moment the version is 5.02.09 and this version doesn’t support the new OpenLab. Unfortunately the update aborts at one point…
Dear all,
we just recently received an upgrade from OpenLab 2.3 to 2.7. We control a Shimadzu with OpenLab. The Shimadzu GC-FID received a new set of drivers during upgrade.
We are now running into problems during calibration of our runs which were…
Hello,
I had my 6890 Plus GC connected to Chemstation B04.02 through a G1369B LAN card recently. Today I had a warning #103 "Sig 1 buffer full" shown in the GC display, probably because the PC went to saver mode over the past couple of days. I restarted…
I'm using the GC6890 with one single column (CP7429). The gas products have to be analyzed by TCD and FID simutaneously. How should I connect the column to TCD and FID? Is it necessary to have a s plitter to split effluent from a single column to TCD…
Hello scientists, I need help
I am using an MP-AES 4200, It worked perfectly until we had a power interruption. Ever since it has kept giving errors such as
1. Plasma Failed to ignite. This may be due to a low supply of Argon or Nitrogen, a deteriorated…
This Information Applies To: Agilent ICP-MS MassHunter Workstation 4.6 or below, and ICP-MS MassHunter Workstation 5.1 and above.
Issue
Guide for identifying the current software version your Agilent ICP-MS system is using, to see if any updates...
This Information Applies To: Agilent OpenLab ChemStation, Agilent OpenLab EZChrom, Agilent OpenLab CDS.
Issue
When users of OpenLab CDS forget their passwords, another user with the right privileges will reset their password, however, sometimes...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to temperature can cause the plasma to shut off or disable plasma ignition. While a warning message will still allow the plasma to light...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
How to view meters in ICP-MS MassHunter Software, or change what meters are selected?
Background
ICP-MS MassHunter allows up to five meters to be displayed at...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to replace the oil mist filter in the MS40+ or MS40-S?
Background
The oil mist filter in the MS40+ or MS40-S should be replaced yearly.
Warning :
...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to check the DS 402 foreline pump to determine if the pump needs maintenance.
Background
The oil cleanliness and oil level in the DS 402 foreline pump should be checked...
This Information Applies To: Agilent ICP-MS systems (7700, 7800, 7850, 7900, 8800, 8900)
Issue
After shutting down and restarting the ICP-MS, sometimes the communication between ICP-MS and PC does not automatically reconnect. It may be necessary...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the Foreline Pump Oil Mist Filter in the DS 402 foreline pump.
Background
The oil mist filter element should be replaced yearly , or when the level of oil in...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil Mist Filter and Odor Element in the E2M18 or E2M18F?
Background
The oil mist filter and odor element should be replaced yearly, or if the...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil in the E2M18 or E2M18F?
Background
The E2M18 oil should be replaced at least every three months or when the oil color indicates it needs...