good day!
tell my please..
I have the air generator and his out pressure consist 52 psi, and and air consumption is 1000 ml/min. the EPC module GC 7890b work in rang 55-80psi. I have 2 detector FID. Tell my - with this generatorom may be worked ?…
yes, it's the purged 2-way splitter. Bottom is column entry, then detector 1 is FID, detector 2 is qtof. (switching FID and qtof position doesn't change anything)
We had 3.7mx0.15mm to qtof and 1mx0.15mm to FID with constant flow 0.8 ml/min for a 1…
Hello, I need to archive a file but the file do not archive. It appears the message "Last archive operation failed"
How can I know why the archive failed and how can resolve it?
Thank you
Thanks Marty, I was afraid of that.
Too bad really since piecewise is the most conventional kind of multi-level calibration.
I train using the example of a typical pH meter where they still naturally calibrate at pH 4, 7, & 10. Therefore there…
You can swap out cylinders to do it, but that means a lot more tubing, etc. to purge when you want to run. With the EPC unit, you would simply load the appropriate method to use it and the switch is done at the instrument. Much less tubing to purge and…
Hello Community
We have a reproducabiility problem on GC-FID's. We run an alkane standard every day in the morning. Peak shapes are looks good but when i compare the total area of the peaks over the last weeks an month, its very bad, i have a standard…
Hi
How do I remove FID signal from the report for a dual TCD & FID GC, we use just TCD detector to analyses gas samples and this issue appear yesterday.
open lab rev. C01.05
Hi Agilent,
Due to helium shortage, we need to change carrier gas for our GC-FID. Most documentation for Agilent suggests either H2 or N2, and the Chemstation configuration shows those options as well.
We are considering using argon, however, I…
This Information Applies To: Agilent ICP-MS MassHunter Workstation 4.6 or below, and ICP-MS MassHunter Workstation 5.1 and above.
Issue
Guide for identifying the current software version your Agilent ICP-MS system is using, to see if any updates...
This Information Applies To: Agilent OpenLab ChemStation, Agilent OpenLab EZChrom, Agilent OpenLab CDS.
Issue
When users of OpenLab CDS forget their passwords, another user with the right privileges will reset their password, however, sometimes...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to temperature can cause the plasma to shut off or disable plasma ignition. While a warning message will still allow the plasma to light...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
How to view meters in ICP-MS MassHunter Software, or change what meters are selected?
Background
ICP-MS MassHunter allows up to five meters to be displayed at...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to replace the oil mist filter in the MS40+ or MS40-S?
Background
The oil mist filter in the MS40+ or MS40-S should be replaced yearly.
Warning :
...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to check the DS 402 foreline pump to determine if the pump needs maintenance.
Background
The oil cleanliness and oil level in the DS 402 foreline pump should be checked...
This Information Applies To: Agilent ICP-MS systems (7700, 7800, 7850, 7900, 8800, 8900)
Issue
After shutting down and restarting the ICP-MS, sometimes the communication between ICP-MS and PC does not automatically reconnect. It may be necessary...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the Foreline Pump Oil Mist Filter in the DS 402 foreline pump.
Background
The oil mist filter element should be replaced yearly , or when the level of oil in...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil Mist Filter and Odor Element in the E2M18 or E2M18F?
Background
The oil mist filter and odor element should be replaced yearly, or if the...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil in the E2M18 or E2M18F?
Background
The E2M18 oil should be replaced at least every three months or when the oil color indicates it needs...