Hi Marty,
I am Yew Mun colleague.
Thanks for your help. we run samples in sequence. The ChemStation version we have is 2.141.0.0 . I will try to setup the report in method and let you know how it goes.
Hema
Hi
I have one problem with my 5977B.
The tune no finish, the principal problem or error is "Tune action stopped: Gain and offset = 0 and peaks are too narrow".
Link behind 7820A GC Remote Control Panel Revision 1.5.5.0 279 MB (current) on page above appears to lead nowhere (May 24). Grateful if this could be fixed. Thanks and regards
To learn more about each component take a look at the Concepts Guide manual included with your system and also Parts 2, 3, and soon 4 of this Blog post.
user-manual-msd-system-5977-concept-guide-G7077-90036-en-agilent.pdf
user-manual-tq-gc-ms-7000…
I'm curious to know how the voltage was applied to all the parts. I guess the repeller will be positively charged, and the lens are alternating and probably with RF to help focusing? But what about the ion source body? Is it grounded?
Also curious,…
If you have trouble viewing the content in the EQP files referenced above, refer to Part of PDF is blank when viewing in Edge, but not when I open in - Microsoft Community
Hi fgunawan , thanks for your reply. I did try with 100% IPA, but I didn't run the pressure test and leak test. I am new with the software and learning independently. I will try to explore these options.
Hi Linds,
Linds
Welcome to the Community. I think this is an excellent question, and something we all face from time to time. Thanks for asking!
I'm going to assume that you have a split/splitless inlet. A PM for this inlet usually includes a liner…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
This Information Applies To: Agilent ICP-MS MassHunter Workstation 4.6 or below, and ICP-MS MassHunter Workstation 5.1 and above.
Issue
Guide for identifying the current software version your Agilent ICP-MS system is using, to see if any updates...
This Information Applies To: Agilent OpenLab ChemStation, Agilent OpenLab EZChrom, Agilent OpenLab CDS.
Issue
When users of OpenLab CDS forget their passwords, another user with the right privileges will reset their password, however, sometimes...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to temperature can cause the plasma to shut off or disable plasma ignition. While a warning message will still allow the plasma to light...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
How to view meters in ICP-MS MassHunter Software, or change what meters are selected?
Background
ICP-MS MassHunter allows up to five meters to be displayed at...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to replace the oil mist filter in the MS40+ or MS40-S?
Background
The oil mist filter in the MS40+ or MS40-S should be replaced yearly.
Warning :
...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to check the DS 402 foreline pump to determine if the pump needs maintenance.
Background
The oil cleanliness and oil level in the DS 402 foreline pump should be checked...
This Information Applies To: Agilent ICP-MS systems (7700, 7800, 7850, 7900, 8800, 8900)
Issue
After shutting down and restarting the ICP-MS, sometimes the communication between ICP-MS and PC does not automatically reconnect. It may be necessary...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the Foreline Pump Oil Mist Filter in the DS 402 foreline pump.
Background
The oil mist filter element should be replaced yearly , or when the level of oil in...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil Mist Filter and Odor Element in the E2M18 or E2M18F?
Background
The oil mist filter and odor element should be replaced yearly, or if the...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil in the E2M18 or E2M18F?
Background
The E2M18 oil should be replaced at least every three months or when the oil color indicates it needs...