Problem: Unable to perform Instrument Configuration for Agilent 1290 LC. The instrument pings at IP address 192.168.254.11 with NO packet loss and connects fine in Agilent Lab Advisor software. Able to perform instrument commands in Lab Advisor.
However…
Hi, I am using a batch file to reprocess data under a different method. The integration and events table look correct on the screen. I have adjusted all of the batch settings options, but the final report only includes the sample information without any…
Date and Time: 07/07/2019 07:26 Program: Agilent MassHunter Workstation Software Qualitative Analysis B.03.01 Build Configuration: Release Message: Retrieving the COM class factory for component with CLSID {4CBCEED8-D9F8-4440-A127-4E840D0573DF} failed…
Hi Everyone,
Please can you help me. We have been having repeatability problems on the HP7890B for a long time and can't get to the bottom of it. Analysing for VOC. I have run lots of RSD measurements (10 injections). A common thing we are seeing…
After most MSD maintenance (filament change/switch, source cleaning, etc...) I seem to have an issue with the baseline dropping in series (offset pattern) for up to 2 weeks afterwards. I'm new to this machine, but I'm in the process of slowly changing…
I looked around but failed to find anything useful. Is there somehow possible to export results/data from SureMass-deconvolution/ID in Unknowns Analysis for further processing and or statistical analysis (besides .CEF-format)?
What are the typical use cases of the Resolve handheld Raman analyzer?
Resolve is a highly sensitive handheld Raman-based chemical identification system that offers real-time detection and identification of unknown military, commercial and homemade…
Hello all I'm looking at designing some standby methods for my 4 GC-FIDs and 3 GC-MSs as they are often sitting idle for 3/4 days a week and are happily consuming helium, hydrogen and generally sucking money away basically for no reason. Turning them…
Hi there, I've recently started using a GCMS (7890A + 5975C MSD). The tune has failed and the GC shows a flat line at 0.5 whenever a sample is run. I've attached all relevant photographs I could think of, including the GC spectra where it all stopped…
I've recently been running into some problems with performing SureMass conversion of data collected on a 6546 LC-QTOF. I'm collecting both profile and centroid MS data using the default data storage thresholds.
Initially, I was running SureMass conversion…
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...