1 uL is injected for PAH.
We do change the liner often and are using the one from all the app notes (with glass wool). We haven't tried a dimpled but do use a dimpled with the PBDE method.
After doing a bunch of troubleshooting over the last few…
I'd like to bump this thread up to the top because in our lab we have had the same problem, and our amazing IT guy was able to solve it!
It turned out that on the PC where the Data Analysis (same version as olabanalyst ) was faulty, it had been installed…
Hi everyone. There are some doubts that I would like to clarify because we're experiencing some drift and sensitivity problems and it may help.
We've already cleaned the cones, lenses and sample introduction system, including the torch.
1) There is…
The peak to the left in the Lithium window is Li6. This is from internal standard solution. Li6 abundance is typically very low and should not be larger than the Li7 peak. When you run start the plasma, is the internal standard (ISTD) line in a nitric…
Hi kalle-h,
Has the method worked well for you in the past? Any changes recently like column trims? Sometimes small pieces of column can get caught inside the modulator fittings and impede flow, which has negative effects on our data.
If your peaks…
Hello brandon.mendoza.ardena ,
It would be hard to tell, not seeing it or hearing it in person. But a good start would be to make sure there is nothing in the carousel that might cause that (broken vials, caps, or various other debris).
Could also…
Hello Durjoy123 ,
The logic board for 7890A+ does not have the same part number as the 7890A. I wouldn't hazard a guess as whether it will "work" or not. It seems like it does in your case.
But as a general rule I would stick to the board part number…
Check out our new article titled Mastering Pressure Management in GPC/SEC Systems , which has been published in the April issue of the Column . The authors are Dr. Daniela Held and Dr. Michael Krämer .
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...