The Introduction Service if purchased includes the following:
Customer guidance to reconfigure the GC from checkout to intended use, including a single injection of a QC standard for the desired method. In the absence of a pre-existing method, the…
The Installation Service if purchased includes the following:
Connection of your existing gas supply to your new equipment. Gas supply may include tanks with regulators, generators placed in proximity to your new equipment, or access ports of existing…
Customer Responsible Site Preparations
Site Preparation Checklist and Site Preparation Guide
Ensure that the appropriate installation hardware has been acquired.
Ensure that the location in which the GC system is being installed meets the requirements…
Typical communication with Agilent activities:
Order Acknowledgement email.
Order confirmation (Thank You) email. Customer can access My Orders Account to track the status of the order.
Ship notification email.
Communications from Consumables…
Hello
I need to do an LC/MSMS method for quantification on a compound that doesn't ionize into [M+H]+ (barely observed) but only into [M-H2O+H]+
Is there a problem with doing MS/MS on a [M-H2O+H]+ parent ion ?
(PS: negative ionization is not an…
Hi again Raina,
as I already told you this cannot be done with just one column, especially with the CO2 concentration up to 20% and water included and the necessity to analyze H2. This is an application we normally build an analyzer for. You need at…
The Digest of upcoming webinars has been updated as of June 5.
In June, you don't want to miss the GC Live Event, GC Live is Back in June with the Next Big Little Thing in GC: The New 8850 GC System on June 6!
Check Out:
Intelligent Analysis of…
Operating like this puts sub-optimal flow into the GCMS ion source of more than 2 ml/min. Please make sure that you have a system with a turbomolecular high vacuum pump and not a diffusion pump as 2 ml/min exceeds the maximum allowable flow into a diffusion…
Exciting news in the world of FTIR spectroscopy!
Agilent has just released MicroLab 5.8 , MicroLab Pharma 5.8 , and MicroLab Expert 1.3 —the software that powers the Cary 630 FTIR spectrometer and Agilent’s handheld and mobile FTIR systems . MicroLab…
Hi Margot,
It may well be that the column performance has deteriorated so much within the 7 months that the EasiVial standards are measured with poorer PDI values. The column performance can be tested with regular plate count determinations. It is a…
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...