1 uL is injected for PAH.
We do change the liner often and are using the one from all the app notes (with glass wool). We haven't tried a dimpled but do use a dimpled with the PBDE method.
After doing a bunch of troubleshooting over the last few…
I'd like to bump this thread up to the top because in our lab we have had the same problem, and our amazing IT guy was able to solve it!
It turned out that on the PC where the Data Analysis (same version as olabanalyst ) was faulty, it had been installed…
Hi everyone. There are some doubts that I would like to clarify because we're experiencing some drift and sensitivity problems and it may help.
We've already cleaned the cones, lenses and sample introduction system, including the torch.
1) There is…
The peak to the left in the Lithium window is Li6. This is from internal standard solution. Li6 abundance is typically very low and should not be larger than the Li7 peak. When you run start the plasma, is the internal standard (ISTD) line in a nitric…
Hi kalle-h,
Has the method worked well for you in the past? Any changes recently like column trims? Sometimes small pieces of column can get caught inside the modulator fittings and impede flow, which has negative effects on our data.
If your peaks…
Hello brandon.mendoza.ardena ,
It would be hard to tell, not seeing it or hearing it in person. But a good start would be to make sure there is nothing in the carousel that might cause that (broken vials, caps, or various other debris).
Could also…
Hello Durjoy123 ,
The logic board for 7890A+ does not have the same part number as the 7890A. I wouldn't hazard a guess as whether it will "work" or not. It seems like it does in your case.
But as a general rule I would stick to the board part number…
Check out our new article titled Mastering Pressure Management in GPC/SEC Systems , which has been published in the April issue of the Column . The authors are Dr. Daniela Held and Dr. Michael Krämer .
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
Can I use reaction volumes larger than 30 μL on the AriaMx?
Resolution
There is no problem with using higher reaction volumes, but the instrument performance can only be...
This Information Applies To: Agilent OpenLab CDS software version 2.3 or higher.
Issue
Chromatogram gridlines can help users to get a better understanding of the scale of the peaks. However, in some cases, the gridlines are not desired, such as...
How to Reset the Agilent GC/MSD Tune File to Default Values
Multiple Results
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software
Issue
If there is a problem with the current tuning parameters and a need to tune from the default parameters, see the following procedure to reset the EI tune file (atune...
This Information Applies To: Agilent OpenLab CDS (version 2.x)
Contents:
In the following procedure, you will find steps to create a multipoint ESTD calibration method with OpenLab CDS 2.X.
Steps to follow:
1. Load the Data
a. From Data...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Chromatographic peak integration is a critical part of accurate and reproducible quantitative data analysis. The integrator type and the integration parameters...
This Information Applies To: Agilent 6200/6400/6500 Series LC/MS Systems
Issue
Instructions on how to fill the calibrant bottle on 6200/6400/6500 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal.
Issue:
Installing the Ion Transfer Capillary after cleaning or replacement. For instructions for installing an ion capillary...
This Information Applies To: AriaMx Real-time PCR System
Issue
The saturation level is unique for each optical module after the offset of calibration factor and background calibration. The FAM, ROX, HEX, CY3 & CY5 optical modules will saturate at...
This Information Applies To: Agilent LC Systems
Issue
While it is possible to combine modules from different HPLC series such as 1100, 1200, 1260 or 1290 series to create a functioning LC system, there are some important topics to consider.
...
Fixes for the "RPC Server Unavailable" Error
Multiple Results
This Information Applies To: Agilent OpenLab CDS
Issue
When launching the instrument Acquisition screen/instrument session, there is an "RPC Server Unavailable" error.
Resolution
Accessing the Services App (Windows)
There are two ways to...