What are the detector voltages? Select the Hardware button, or Hardware/Dashboard from Task manager, and click the Detector image. Select EM setting. What are the voltages for Discriminator, Analog HV, and Pulse HV?
Was the instrument off, for an extended…
I have observed that when a method is transferred to a new system, you need to save it in the new system before using it. If you just copy the method and use it, sometimes it fails. Just by saving it, it makes it work. I guess it saves some defaults from…
I was never able to do glycols via headspsce in the past. The only way I was able to do them was direct injection and FID. 5890 using megabore column. Maybe you could try SPME.
Hi Lycrecia,
We checked the volume calibration section and we did the full range volume dispense, as described in the manual. However, we are not sure which value we should add to the actual volume in the volume calibration screen. Do we need to do…
I am running GC 6890 (FID detector) alongside G1888 headspace.
I had noticed 4 of my later eluting peaks got increasingly worse in terms of shape and reproducibility. After running blanks (no injection and also blank vials), it seemed like the cause…
it does not work,
I tried to install openlab v2.4 manually, the installation failed at the agilent platform in the install or upgrade content management part,
This is a 5977A that was built in mid-2015. How many runs on it? . High Energy Dynode (HED) related, Electron Multiplier (EM) related, signal related, or electronics related.
The first thing to try is to go into manual tune and turn OFF the HED. I'd…
Hello, Your question brings some additional questions for me. You mentioned that your rescans are failing eventhough the product is correct. Is your method robust enough. You should not see many fails in a batch if the instrument is properly operated…
Hello Andy, thanks for your answer. It would be possible, however we would like to automate our analysis as much as possible. A manual calculation of the concentrations, depending on the initial weight, would make us go a step in the wrong direction.…
hello,I had the same problem as you to make the sum of impurities, I searched in the forum and I found the following formulas, to be verified because I am not an expert in formulas but it worked
ListImpND (Type string, scope signal) If (Count(CurrentSignal…
This Information Applies To: Agilent G1312X and G7112X binary pumps.
Issue:
A blockage before the pressure sensor, e.g. in a pump head, will not give a high pressure or overpressure system error. Instead, the pump may show one of various error messages...
This Information Applies To: Agilent 1100, 1200, 1260 LC Pumps.
Issue:
The following procedure allows the cleaning of residue from the pump's check valves, often caused by polymerization of aged acetonitrile or salt-based solutions that may prevent...
This Information Applies To: Agilent LC Systems
Issue
After analyzing dirty or concentrated samples, some sample compounds may retain in the column and other parts of the HPLC system. If the column re-equilibration after each run is not enough to...
This Information Applies To: Agilent G7167A/B Multisampler.
Issue:
Required when:
The needle is visibly damaged.
Leaks or blockages in the vialsampler are observed, especially between the needle and needle seat.
The limit for the needle...
This Information Applies To: Agilent Autosampler modules G1367A, G1367B, G1367C, and G1367D.
Issue:
The removal and installation of the needle assembly in these older autosampler modules can be tricky and may require patience and the correct technique...
This Information Applies To: All standard analytical scale Agilent 1100/1200/1260/1290 Infinity / Infinity II LC system configurations: Single Pump (Isocratic, Quaternary, or Binary) with Manual Purge Valve. Does not apply to systems with Agilent G7167A...
This Information Applies To: All Agilent LC modules (except hosted modules).
Issue:
When a module does not initialize correctly or it is not recognized by the software, it is recommended to call our Remote Support Representatives to troubleshoot...
This Information Applies To: All Agilent LC pump modules with MCGV installed (quaternary pumps)
Issue:
Shifting retention times: The composition of the mobile phase in liquid chromatography directly influences retention times. If any of the channels...
This Information Applies To: All Agilent liquid chromatography instruments, Lab Advisor
Issue:
The error message 'Could not open channel RD' pops up when performing diagnostic tests in Lab Advisor. Retrying the test is not helping.
Resolution...
This Information Applies To: Agilent Lab Advisor Software for any Agilent LC System.
Issue:
To successfully troubleshoot an Agilent LC system or module, the System Report is an essential resource. Agilent Support representatives may ask you to provide...