Hello Lucas_S ,
Based on your follow-up explanation in this discussion -
(+) Macro for Batch Export of CSV in OpenLab CDS C.01.10 to a unique archive. - Forum - Chromatography Software - Agilent Community
I don't believe this macro could be easily…
For others who may find this interesting. Looking at the GPIB set up with NI MAX you see 2 'instruments' with primary addresses of 9 and 20. The instrument at '9' seems to work fine. Thus I can see the machine warming up and going through the wavelengths…
I am using an Agilent 6460 Triple Quad and have been dealing with a terribly low signal for the past few days, the signal appears at an abundance of 30 to 50 as a baseline only. I analyzed different compounds with different concentrations, the Tune mix…
Hi Sabbas, thank you for your answer. I'm sorry I couldn't have answered you sooner.
We're using Cary 3500 with Cary UV workstation version 1.3.5, so we couldn't perform like you said. We have to lower the threshold to find peaks and it is quite inconvenient…
Joining associations that specialize in ultra-high voltage can be beneficial for PenflexCorp. This may include associations of electrical or power engineers, as well as groups specializing in the design and standardization of equipment for high-voltage…
The Digest of upcoming webinars has been updated as of April 11.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
The Background values are so called "off mass background".
This could indicate an electronics or contamination problem of the quad.
In your case, the values are still quite ok.
I would guess, one of the lenses has a setting which is causing this…
Hello everybody!
We have the issue that in our run (ca. 100 - 200 samples, 7 min each) for like 20 samples there is no signal, just the technical background noise. Not even the peak that is in the Blank appears. An the it sowly comes back over 2 samples…
This Information Applies To: Agilent G1312X and G7112X binary pumps.
Issue:
A blockage before the pressure sensor, e.g. in a pump head, will not give a high pressure or overpressure system error. Instead, the pump may show one of various error messages...
This Information Applies To: Agilent 1100, 1200, 1260 LC Pumps.
Issue:
The following procedure allows the cleaning of residue from the pump's check valves, often caused by polymerization of aged acetonitrile or salt-based solutions that may prevent...
This Information Applies To: Agilent LC Systems
Issue
After analyzing dirty or concentrated samples, some sample compounds may retain in the column and other parts of the HPLC system. If the column re-equilibration after each run is not enough to...
This Information Applies To: Agilent G7167A/B Multisampler.
Issue:
Required when:
The needle is visibly damaged.
Leaks or blockages in the vialsampler are observed, especially between the needle and needle seat.
The limit for the needle...
This Information Applies To: Agilent Autosampler modules G1367A, G1367B, G1367C, and G1367D.
Issue:
The removal and installation of the needle assembly in these older autosampler modules can be tricky and may require patience and the correct technique...
This Information Applies To: All standard analytical scale Agilent 1100/1200/1260/1290 Infinity / Infinity II LC system configurations: Single Pump (Isocratic, Quaternary, or Binary) with Manual Purge Valve. Does not apply to systems with Agilent G7167A...
This Information Applies To: All Agilent LC modules (except hosted modules).
Issue:
When a module does not initialize correctly or it is not recognized by the software, it is recommended to call our Remote Support Representatives to troubleshoot...
This Information Applies To: All Agilent LC pump modules with MCGV installed (quaternary pumps)
Issue:
Shifting retention times: The composition of the mobile phase in liquid chromatography directly influences retention times. If any of the channels...
This Information Applies To: All Agilent liquid chromatography instruments, Lab Advisor
Issue:
The error message 'Could not open channel RD' pops up when performing diagnostic tests in Lab Advisor. Retrying the test is not helping.
Resolution...
This Information Applies To: Agilent Lab Advisor Software for any Agilent LC System.
Issue:
To successfully troubleshoot an Agilent LC system or module, the System Report is an essential resource. Agilent Support representatives may ask you to provide...