When the tuning is done at 3200 (+) everything is fine. When I change it to tune at 1700 (+) the masses are reasonably accurate. After it gets to the third mass (620) it appears that the entire spectrum shifts by about 1.5 AMU and the tuning fails. There…
Hi Siddhartha,
Thank you for contacting Cell Analysis Technical Support. Can you please go ahead and send us your System Files so that we can see what might be going on? These can be accessed in the Help Section of the Wave software. You can select…
Hello thank you very much for your response, thanks for the firmware data, the degasser worked perfect, the firmware change no longer, and I can not find the previous version. and are from the 6.80, but how is it possible that a team of thousands of dollars…
Thanks for the reply. I am monitoring at 254 nm. Higher wavelengths do not show that drift. It must be related to the THF (I am using unstabilized) but I do not see how.
Hello, we have an mp aes 4210, we cannot turn it on and we get this error "PLASMA_IGNITION_SHER_GAS_PRESSURE. POP gas pressure out of range". We performed the gas test but it does not pass.
We contacted an Agilent agent and he told us that the problem…
Thanks for the info! What I was thinking about is that some instruments, like GC/MS units sometimes come with recommendations to not put the unit on a UPS due to problems it can cause with the oven. So, I was wondering if Agilent had anything specific…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Fragment Analyzer controller software
Issue:
Over time the dynamic coating polymer on the capillaries needs to be refreshed. Failure to do so can lead to a loss of performance. Indicators...
This Information Applies To: Agilent ICP-MS (7700/7800/7850/7900/8800/8900)
Issue
Elevated doubly charged values that are greater than 3% for x-lens configuration or greater than 7% for s-lens configuration, can be caused by contamination, or an...
This Information Applies To: Agilent 6200 Series TOF and 6500 Series Q-TOF Systems
Issue
Instructions on how to correctly dilute the tune mix for 6200 Series TOF and 6500 Series Q-TOF systems depending on source type.
Background
If the Tune...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
The Agilent MassHunter Qualitative software can generate qualitative analysis reports, which may include sample chromatogram information and sample...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0 or higher
Issue
Identifying compounds using a spectral library is essential in qualitative analysis. This article will describe how to load a data file and...
This Information Applies To: Agilent ICP-MS Systems
Issue
The Helium cell gas line on the ICP-MS may be contaminated with air and moisture in case of a tank replacement, or if the instrument was not used for an extended amount of time. Purging the...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The Calibration Curve window tools help with setting an appropriate calibration curve for each compound in the calibration table.
The Calibration Curve window...
This Information Applies To: Agilent MassHunter Quantitative Analysis "Quant-My-Way" user interface (version B.09.00 or later)
Issue
To process the data files in the batch and obtain quantitative results, you must either create a new quantitative...
This Information Applies To: Agilent MassHunter Qualitative and Quantitative Analysis
Issue
Calculation of signal-to-noise in MassHunter is done using the same routine for both Qualitative and Quantitative Analysis. However, there are differences...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Multiple samples can be run without user intervention using an Automated Liquid Sampler (ALS) in combination with a Sequence.
Users can perform simple edits...