Hello
I recommend to replace X-belt.
P/N 5410047500 Belt timing – 880 mm
When initializing if the belt tension is not enough, It could be failed.
Please check it.
We have several 1220 Infinity II system (G4290B) on our location. They are connected same type of computers with same windows. Only one of them has connection issue as below. Since there is connection to detector (I can control detector fully), I am not…
Thanks! To add, I just ran the software verification tool and the MassHunter GCMSAcq_base.xml report failed. File Report Summary
Missing files or invalid files found:
Invalid Files :1
No system file difference found
Invalid Files …
Hi there! We have a Cary 60. We are doing preventive maintenance, but the noise test fails and it took up to three or four times to get a successful result. What can we do to improve this and get a passed result the first time?
Morning, You are correct. I am running OpenLab CDS ChemStation. Rev code = C.01.04 [35]. Intelligent Reporting product version A.01.04.122. The system suitability issue is that I'm only getting the TCD satistical results. The FID result are not printing…
Hello Lars, Thanks for your reply. Unfortunately, there is no flow meter meter installed. So you are saying that, in your case without stopping gas flow before GC injection, you are only getting 1-2% deviation in FID response? If possible could you explain…
Hi I have a very basic question, please correct me if I am wrong. I am using GC 7820 with FID detector. Flow , Pressure everything was set by another technician before I started. I know for Back Detector everything is what is set by the Technician in…
Hi,
Our QTOF system failed to do a polarity switch from positive to negative. But it works fine at the positive mode. Just wondering if anybody knows the problem. Here is the instrument log record:
Time EventType EventSource Category Description User…
When running a calibration on the GCMS the internal standard increases the entire time for all of our standards. It goes from around 1.9 million for the bottom of the calibration to 3.2 million. Recent things that we have done that should help eliminate…
This Information Applies To: Agilent OpenLab ChemStation
Issue
This article describes the fundamentals of noise determination and calculation in Agilent OpenLab ChemStation to report the signal-to-noise ratio.
Tips : To report the...
This Information Applies To: Agilent OpenLab CDS
Issue
The default workflow for OpenLab CDS is the following: Reprocess Results > Save Results > Print Results . This is the recommended workflow for regulated environments.
For nonregulated environments...
This Information Applies To: ICP-MS MassHunter 4.x/5.x
Issue
Reviewing the latest Performance Report, and Performance Report History is a useful tool for troubleshooting ICP-MS instrument performance issues. Historical sensitivity, background, precision...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to perform routine maintenance on the Agilent ICP-MS Torch.
Background
Deposits on the torch can be removed by routine maintenance. Maintenance frequency...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...