Does anymore have./know of a macro for Agilent Enhanced Data Analysis Software (MSD Chemstation G1701FA F.01.03.2357) that enables the integration of a file (FID and TIC using the ChemStation integrator) to be saved so when you re-open the data file you…
Hello,
I have been struggling with this coding error with OpenLabs Chemstation Report layout, I'm hoping the Agilent community may have a solution to my problem.
I'm told that the coding language for the Openlabs report templates is pretty much the…
jhagel is correct, do not change PE (Yellow) to PTFE (black) seals in round headed pumps (1290 Infinity and Infinity II as well as G7014C). Both seal types have benefits and downsides: While the black seals are generally better when using them with reverse…
Hello,
I have a G6545 QTOF / 1260 HPLC system that came with an HP Z440 workstation with Windows 10 as part of the purchase from Agilent. The workstation is ~ 3 years old. The instrument was running normally over the weekend -- when I came back, the…
Fortunately yes, so I am covered from that point of view The GC over here is a combo MS-FID machine which can be build to either MS of FID mode. It was in FID mode the last couple of days. Just rebuild the GC to MS mode, but I didnt perfom a full-on cleaning…
I'm trying to develop a method for ethanol via headspace. I am using Restek standard Residual Solvents #1 (34105) for the curve. My instrument is Agilent 6890 GC-FID with CTC PAL COMBI autosampler for headspace.
I ran residual solvent curve at high…
Want to quantify or at least qualify trifluoroacetic acid (tfa) on our column, which is almost exclusively used for quantifying propionic acid, with acetic acid as the internal standard. Both dissolved in acetonitrile. It seems like tfa would work, but…
Thank you for your question. Unusual high low voltage error is a common instrument and accessory maintenance related and not instrument hardware related issue. Typically, when you see that error, under logbook of your run, you will see chip map. Please…
Hi dmarchini, I have attached a guide for some recommended spares. The questions of cost to maintain any GC is a difficult one as the application and sample amount plays a major role. Replacement of the consumables will vary because of this. The guard…
GC and GCMS Supplies Recommendations for POIS 2020.pdf
This Information Applies To: ICP-MS MassHunter 4.x/5.x
Issue
Reviewing the latest Performance Report, and Performance Report History is a useful tool for troubleshooting ICP-MS instrument performance issues. Historical sensitivity, background, precision...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to perform routine maintenance on the Agilent ICP-MS Torch.
Background
Deposits on the torch can be removed by routine maintenance. Maintenance frequency...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...