Hello everyone!
I'm currently working on a new (for my company) method of quantifying acrolein by GC-FID. I have a big problem with the appropriate weight of the standard. According to the article, I should add the right amount of acrolein to the CS2…
Thanks, Marty! I'm unfamiliar with intelligent reporter, but it looks like that's what I need. This would be for a single injection. I would need it to display as another line under the main results, with an obvious notation, like pass/fail or reportable…
Hello, I have the new MassHunter. Well, my P/A factor has failed. :-( do I correct this? I don't understand how to correct it. I am supposed to select a measurement from the "Load Mass List from Method". and added it. Unfortunately, the Current Value…
We are trying install OpenLab LTS 01.11 Aug 2022 onto our Windows 10 system; however, the System Preparation Tool states that the Check Pending Reboot step fails even after rebooting the computer.
This is a known issue with the software, but there is…
The signal count is lower between the DFTTP/Degrad check with each analytical run. The analytical run acquisition is pointing to the dfttp tune file.
A new syringe has been replaced. Inlet maintenance is done every 4-5 analytical runs; this instrument…
Hello, friends! We have installed a new AAS 280FS device. After installation, the device fails Frequency Diagnostic and Power supply Diagnostic tests according to the SVD software. Please advice, what we can do? Thank you.
We have intention to upgrade existing Chemstation B version to OpenLab Chemstation C.01.10 version for 6890N and 6890A GC both equipped with TPI inlet (from VAR) and FID.
We are not sure if the upgraded OpenLab CDS able to recognise or support TPI inlet…
Thanks for your quick response
but i want to put this limits ( for example 90% to 110%) in my CC editor and in my report called the final result (for example 95%) PASSED and (for example 85%) FAILED. So , how can i translate this limits for different…
Hi all,
I work on a 6470A QQQ. The MS was shut down for maintenance, change of oil of the rough pump, source cleaning, AJS ESI needle replacement and capillary replacement were performed.
Rough vac and high vac values are better than before shutting…
Hello igorvlad
I’m sorry for the delayed reply to your message. Do you still need assistance with this? If you do, please take into consideration the notes below. However, if the issue was resolved, could you please share what the resolution was?…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...