Hello Lucas_S ,
Based on your follow-up explanation in this discussion -
(+) Macro for Batch Export of CSV in OpenLab CDS C.01.10 to a unique archive. - Forum - Chromatography Software - Agilent Community
I don't believe this macro could be easily…
For others who may find this interesting. Looking at the GPIB set up with NI MAX you see 2 'instruments' with primary addresses of 9 and 20. The instrument at '9' seems to work fine. Thus I can see the machine warming up and going through the wavelengths…
I am using an Agilent 6460 Triple Quad and have been dealing with a terribly low signal for the past few days, the signal appears at an abundance of 30 to 50 as a baseline only. I analyzed different compounds with different concentrations, the Tune mix…
Hi Sabbas, thank you for your answer. I'm sorry I couldn't have answered you sooner.
We're using Cary 3500 with Cary UV workstation version 1.3.5, so we couldn't perform like you said. We have to lower the threshold to find peaks and it is quite inconvenient…
Joining associations that specialize in ultra-high voltage can be beneficial for PenflexCorp. This may include associations of electrical or power engineers, as well as groups specializing in the design and standardization of equipment for high-voltage…
The Digest of upcoming webinars has been updated as of April 11.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
The Background values are so called "off mass background".
This could indicate an electronics or contamination problem of the quad.
In your case, the values are still quite ok.
I would guess, one of the lenses has a setting which is causing this…
Hello everybody!
We have the issue that in our run (ca. 100 - 200 samples, 7 min each) for like 20 samples there is no signal, just the technical background noise. Not even the peak that is in the Blank appears. An the it sowly comes back over 2 samples…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to perform routine maintenance on the Agilent ICP-MS Torch.
Background
Deposits on the torch can be removed by routine maintenance. Maintenance frequency...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...