Thank you very much for your quick answer. It's very important for me to understand the concept well, so I have some consistency problems with the response of the compounds.
The Digest of upcoming webinars has been updated as of May 23.
The new Agilent Community Group, GPC/SEC Solutions Group hosted a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules …
For more information, check out the application note Five Keys to Unlock Maximum Performance in the Analysis of Over 200 Pesticides in Challenging Food Matrices .
Recommended parts from the video:
Self-tightening, collared column nut for use with…
Hello,
Are you still having low flow issues on your AA? Did replacing the nebulizer assembly help?
Do you change the flame gases for your methods? If so, call up a default air/acetylene method. You will need a lamp of that element. Go to Optimize…
It is hard to see from the picture which stator this is. If it is the 7 port for ISIS3 then the part number of just the stator is:
G8411-80121 Stator, for 7 port, 2 position inject valve.
Hello,
The penning gauge is now referred to as the ion gauge. It is located on the right side, front of the analyzer chamber. It is easily identified by the blue cable connected to the back of the gauge. Make sure to put the instrument into Shutdown…
With the rapid move towards electrification, lithium-ion battery (LIB) production is expanding to keep up with global demands. Strict quality control of the materials used in these batteries is paramount for battery safety and performance.
The Agilent…
This single-channel GC offers the built-in intelligence and high performance of the 8890 GC in about half the footprint. The small column oven enables fast thermal cycling, which contributes to a reduction in power usage of up to 30%. Ease of maintenance…
Hello glee168 ,
I never saw that error nor heard of people getting that. Where is that error appearing, on the PC, on the GC display, or is it the tool that is giving that error? Or, were you running the chromatography software while the FW update…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...