Hi, I am using Agilent 7820A GC-FID with EZChrom Elite data system. I am absolutely new to GC. Past few days I am trying to do a multi-level calibration for my analyte. But totally confused with the options I find in the software. So far I have done the…
Hii,
I'm looking for some help or suggestion to unlock my 5973 MS.
In the process of updating the FW from 5.01.62 to 5.02.07, required by MSD Chemstation E.02.01, I received a request for USER and PASS that did not stop the procedure, but eventually…
I'm in IT support for a chemistry lab using an old Varian Cary Eclipse Fluorescence Spectrophotometer. The old PC the lab tech were using had some issues during Scan Setup where they were unable to input the necessary parameters for their measurements…
Hi carcuri13, This sounds like the heater sensor assy is failing. If the change is rapid in temperature , the thermal block is not capable of changing quickly. The heater sensor would need to be replaced. Regards James
"Instrument" software of our LC doesn´t show analysis results anymore. When we try to open result data, it shows the message "Incomplete results. 1 out 1 data files do not have a result file and will not show up on the report. To generate results recalculate…
Thank you Paul. I was able to do all that now. I also did inlet maintenance:
opened the inlet completely, replaced guard column+fittings (ferrules on both ends, column nut to Ultimate union), gold seal+washer, and inlet reducing nut (used a better looking…
At some point I believe OpenLab CDS software, Rev. C.01.08 [210], was corrupted for one GC. We run two Agilent 7890B's on the software. There are two issues for GC-4, file path "\chem station\1\". The other GC \2\ is running perfectly. No issues at all…
When we run standards (or ICAL) the internal standards get slightly higher the higher the concentration of the standard. The analyst has mentioned this with samples as well (dirty samples vs clean samples). When we run blanks or clean samples the IS goes…
A few things to check: - use the latest version of LabAdvisor (currently B.02.14 SP1) - thoroughly purge the entire pump with the selected solvent - double-check or replace the blank nut - using a piece of tissue, check all physical connections for leaks…
Hi Ron, cheers for that. I have made a note of that method flow, thanks, but it's looking like it may be a touch moot; I cannot find the discs anywhere. I have sent an email to our IT team to see if they have them, but otherwise I'm at a bit of a loss…
This Information Applies To: Agilent OpenLab ChemStation
Issue
When launching OpenLab ChemStation Online or Offline session, the following error messages “ ChemStation ChemMain has stopped working ” or " There is a problem with Adobe Acrobat/Reader...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Agilent Femto Pulse, Agilent ZAG DNA Analyzer
Issue: The instrument encounters a run error, Run Aborted, Position fault: Did not reach target Z position ( Figure 1 ) . This error...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, Oligo Pro II
Issue:
This article explains the steps to take after installing a brand new array in the Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, and...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer systems, RNA kit (15 nt) (p/n DNF-471-0500/1000), HS RNA kit (15 nt) (p/n DNF-472-0500/1000), Small RNA kit (p/n DNF-470-0275)
Issue
Which kit should be used to analyze single...
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...