The Digest of upcoming webinars has been updated as of March 7.
Notable additions include:
Atomic (1)
Automated Electrophoresis (1)
Chromatography and Mass Spec (12)
Vacuum Solutions Series (3)
Check Out:
The Analysis of Petroleum…
Iron(II)fumarate is a salt with a melting point of 280 °C and therefore not suitable for gas chromatographic analysis. You need to remove the metal ion and set the fumaric acid free, get the sample dry to derivatize it with BSTFA or do an esterification…
Hello,
The infinity II is the HPLC hardware, that can be controlled by several different Agilent software platforms CDS 2.x, Chemstation, EZChrom plus third party data systems. In most of the Agilent software, if you can find the help menus, there…
Hello,
You cannot change the presentation of that results preview screen directly in Chemstation. You might be able to change the behavior using macros, but no configuration is available by default.
Marty
Hello,
Based on the ladder profile in the screenshot you shared, it appears that you are running the DNF-905 kit.
In reference to the issue of missing sample signal or blank lanes, since ladder and marker peaks are present as expected, issue is likely…
K_Ruiter The error you are experiencing could be related to the ESW/FW version used on the Ultivo (I would assume you are using ESW 6.74.3). If you are willing to upgrade acquisition software to the latest (MH 12.1), the new ESW/FW for the TQ may resolve…
This Information Applies To: Agilent OpenLab ChemStation
Issue
When launching OpenLab ChemStation Online or Offline session, the following error messages “ ChemStation ChemMain has stopped working ” or " There is a problem with Adobe Acrobat/Reader...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Agilent Femto Pulse, Agilent ZAG DNA Analyzer
Issue: The instrument encounters a run error, Run Aborted, Position fault: Did not reach target Z position ( Figure 1 ) . This error...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, Oligo Pro II
Issue:
This article explains the steps to take after installing a brand new array in the Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG, and...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer systems, RNA kit (15 nt) (p/n DNF-471-0500/1000), HS RNA kit (15 nt) (p/n DNF-472-0500/1000), Small RNA kit (p/n DNF-470-0275)
Issue
Which kit should be used to analyze single...
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...