Hi I'm using chemstation revision G1701EA E.02.02.1431 and the last successful launch was a day yesterday. It seems the malfunction accrued (during a "run" with a "new" method we are trying. involves FID HS for DCM residue, all the vials were sampled…
The Agilent Equipment Qualification Plan (EQP) for OQ is freely available on the Agilent website for potential customers to review. I have attached the standard EQP OQ for GC
Hello everyone,
I have created a simultaneous SIM/scan method and we're using a HS-SPME-GC-MS system (GC: Agilent 7890 A GC-System; MS: Agilent 5975C Inert XL MSD with Triple-Axis Detector; Software: Chemstation G1701EA E.02.00.493).
We get a TIC…
Hi community,
maybe someone has an idea what I could do, before a technician comes over.
During my absence my colleagues told me that our HPLC (1260 Vialsampler, 1260 Inf II Flex pump, TCC, FC-AS, DAD) does show a peak shift of about 3 to 10 minutes…
Were you able to join us on April 11th for our Agilent GC Live session? If so, we would like to hear your thoughts and questions. If you missed it, please see the video below.
Time stamps refer to the above video.
(14:05) What is…
We work with a Q-TOF 6545 and it fails positive auto tune. Is there anyone who knows this error, what causes it and what can be done to rectify this? Thank you
Hello, I am trying to generate a streamlined intelligent report in OpenLab where we can capture all peaks of our SEC gel filtration standard in a single table and be able to evaluate APD Pass/Fail for each peak and Resolution between BGG and Ovalbumin…
Yes, it is the constant flow mode. The following is the method I am using: Carrier gas: Helium Carrier gas flow rate: 1 mL/min (constant flow) Injection volume: 1 μL Injection port temperature: 250 °C Split injection ratio: 30:1 Initial oven temperature…
Thanks for the feedback. I have re-optimized the lamp alignment, but I didn’t get much (if any) improvement. I also made some adjustments to the sample position, which I think helped a little. I think some users have been fiddling with the sample position…
This Information Applies To: Agilent 5100, 5110, 5800, and 5900 ICP-OES systems
Issue
When troubleshooting communication issues between Agilent 5000 Series ICP-OES and the instrument controlling computer, it is necessary to know the IP address of...
This Information Applies To: Agilent 5000 series ICP-OES systems
Issue
Poor or high relative standard deviation, or a noisy signal is an indication of poor precision during analysis.
Resolution
There are many potential causes for an instrument...
This Information Applies To: Agilent 5000 series ICP-OES systems
Issue
Instrument calibration (wavelength), detector calibration (dark current, or method calibration (worksheet) failure.
Resolution
There are several reasons why a calibration...
This Information Applies To: Agilent 5000 series ICP-OES
Issue
Exhaust temperature and requirements for laboratory site preparation
Background
Certain parameters will impact the actual temperature of the plasma exhaust. Some of these factors...
This Information Applies To: Agilent 700 Series ICP-OES instruments
Issue:
It is important that a torch alignment is performed to ensure that the optics are optimized and are focused on the analytical zone of the plasma. This alignment procedure...
This Information Applies To: Agilent 5800/5900 ICP-OES
Issue:
The instrument requires clean, dry, noncorrosive air for cooling purposes. The air enters the instrument through an air supply vent located beside the chimney on the top of the instrument...
This Information Applies To: Agilent 5100, 5110, 5800, 5900 ICP-OES systems
Issue
The ICP-OES spray chamber filters the sample droplets created by the nebulizer. Larger droplets fall to the chamber drain, while the smaller droplets are introduced...
This Information Applies To: Agilent 5000 ICP-OES Series and Agilent ICP Expert Software
Issue
How to connect Agilent 5000 series ICP-OES systems to Agilent ICP Expert software via LAN
Steps to Follow
How to connect Agilent 5000 series ICP...
This Information Applies To: 5000 series ICP-OES (5100/5110/5800/5900), ICP Expert
Issue
How to Reset the AVS 6/7 after maintenance or when a red LED is visible
Steps to follow
Tips : Instructions for changing the AVS switching...
This Information Applies To: Agilent 5100, 5110, 5800, 5900 ICP-OES
Issue
The axial pre-optic window needs checking from time to time to ensure it is clean.
If the axial pre-optic window is dirty, it must be cleaned or replaced to ensure adequate...