Larger are the orifices of the cones, particularly the sample cone, more chance you have to get the IF/Bk pressure errors. Usually when the sample cone is too used then is passing too much air or whatever trough it at the interface, and the ICP senses…
Hello,
I have inherited a 5975 MSD and when I go to autotune, there are no peaks present and the tune fails. I get alternating errors "Gain and Offset = 0 and peaks are too narrow" or "Tune action stopped: The valid Range for Ent Lens Offset is 0…
It may. I'll review the Report Template Editor Concepts Guide and your post (@wydnaa) and see how this works .As for how we would calculate this manually, I'd just divide the result but the expected value (in our case 0.02 ppm) and multiply this by 100…
Hi, I am using a 6890 GC in split mode with an isothermal temperature and no flow ramp and operating in constant pressure mode. Please can you advise how using the setting constant makeup flow for the FID detector is different to constant column and makeup…
I have a GC 6850 with an FID. I'll have to upgrade to Windows 10 soon, because Windows will no longer provide security updates for Windows 7. If I upgrade my computer to Windows 10, is there a ChemStation version that's compatible with the 6850 and Windows…
Won't start without a "Mating Connector"
I use RS232 to control the pump. The mating connector is not present,
The manual says short pins 4 and 5 and pins 8 and 9 of the IO port.
This results in ramp-up and fail.
What is the correct wiring for…
Hi, We observed an error during autotune of QQQ GCMS as "Peak width gain failed", When it was occurred and what is the reason for the repeat error, Autotune was not completed due to " Peak width gain failed".
Please suggest the recommendations and possibility…
Hello Michael,
It's kind of a yes and no answer. Technically, the wavelength calibration will have failed because the strontium wavelength was not found - so you will see this if you check the results. Practically this is unlikely to impact operation…
Hello,
Our 6545 QTOF has been idle for a few weeks. When I checked the computer today, I found that "communication failed" errors had started appearing a few days after the instrument was last put to Standby. I'm not sure what happened as I don't think…
My manager is wanting me to add pass/fail system suitability assessments to my reports/processing methods. In order to limit my validation work and minimize the number of report templates that I am maintaining, I am trying to keep the report adaptive…
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software version B.02.08 or later
Issue
When printing a report to PDF or HTML with the 2100 Expert software, the error "Failed to Generate Report" appears.
Background
This error...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue
Resetting upper or lower markers from their automatically assigned settings in the Agilent 2100 Expert software.
Background
The Agilent 2100 Expert software...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert Software
Issue
Samples with a broad signal such as NGS smears should be analyzed by setting up a region. Analyzing a region is also termed smear analysis.
Steps to Follow...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RIN NA, Error 4501, RNA 6000 Nano kit (p/n 5067–1511 ), RNA 6000 Pico kit (p/n 5067–1513 )
Issue:
The RIN is not displayed in the software or shows as NA. If the RIN is NA, the...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RNA 6000 Nano kit (p/n 5067-1511), RNA 6000 Pico kit (p/n 5067-1513)
Issue:
Which assay should be selected in the Agilent 2100 Expert software when running yeast total RNA samples...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software, RNA assay, DNA assay, Protein assay
Issue:
The X-axis description toggle icon in the Agilent 2100 Expert software toolbar ( Figure 1 ) does not change the X-axis from time...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Expert software
Issue:
Sometimes the text and images can appear to be the wrong size and in the wrong place in PDF reports generated in Agilent 2100 Expert software (see Figure 1 ).
Figure 1 . Example of wrong...