I am using an Agilent 6460 Triple Quad and have been dealing with a terribly low signal for the past few days, the signal appears at an abundance of 30 to 50 as a baseline only. I analyzed different compounds with different concentrations, the Tune mix…
Hi Sabbas, thank you for your answer. I'm sorry I couldn't have answered you sooner.
We're using Cary 3500 with Cary UV workstation version 1.3.5, so we couldn't perform like you said. We have to lower the threshold to find peaks and it is quite inconvenient…
Joining associations that specialize in ultra-high voltage can be beneficial for PenflexCorp. This may include associations of electrical or power engineers, as well as groups specializing in the design and standardization of equipment for high-voltage…
The Digest of upcoming webinars has been updated as of April 11.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
The Background values are so called "off mass background".
This could indicate an electronics or contamination problem of the quad.
In your case, the values are still quite ok.
I would guess, one of the lenses has a setting which is causing this…
Hello everybody!
We have the issue that in our run (ca. 100 - 200 samples, 7 min each) for like 20 samples there is no signal, just the technical background noise. Not even the peak that is in the Blank appears. An the it sowly comes back over 2 samples…
Hi,
Apparatus 4 is the only USP Apparatus Agilent doesn't make. I would recommend reaching out to an App 4 vendor for support based on how you're using it (open/closed loop, sampling volumes, etc. that need to be considered). If we can help you with…
Yo tengo también una consulta sobre el software. Cómo podría volver a leer una muestra sin que se distorsione el informe al momento de imprimirlo? Y sin tener que volver a calibrar.
Your vial's cap is loose or deformed?
Many crimping and de-capping problems can be solved by two very general suggestions:
Verify the cap is properly crimped
Adjust the electronic crimper/de-capper as necessary
Verify the cap is properly…
Hi Martin,
How would I go about using conditional formatting for the Area P/F field to color the field green for Pass and Red for Fail? I'm not quite sure what type of exprssion to use.
This Information Applies To: Agilent 4200 TapeStation 4150 TapeStation, TapeStation controller software
Issue
The system verification can be run to check the TapeStation performance, for example, when you suspect an instrument hardware fault.
...
This Information Applies To: Agilent 4200 and 4150 TapeStation software.
Issue
How to uninstall and reinstall the 4200 and 4150 TapeStation software.
Background
An uninstallation and reinstallation of the TapeStation software should be performed...
This Information Applies To: 2200 TapeStation instruments, 2200 TapeStation controller software
Issue:
The Agilent 2200 TapeStation controller software won't launch but displays the correct serial number in the top-right corner of the loading screen...
This Information Applies To: 4200, 4150 and 2200 TapeStation, TapeStation analysis software A02.02 or higher.
Issue:
When using the Agilent 4200, 4150 and 2200 TapeStation systems, the DV 200 of FFPE RNA samples can be calculated within the TapeStation...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, ProSize Data Analysis Software
Issue
How to export a ladder as a size calibration file and import it into a different run in ProSize.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...