Hello,
You turned the value back into a number by dividing by10 outside the formatnumber statement. I would just place the entire statement in a Val() function and then format the column as 1 decimal place.
Marty
=Val( If ( Signal_Name like…
Hello staceylouie ,
I apologize for the delayed response.
The error you are seeing was a known issue in that revision due to no structure match being found for the selected compound. The workaround for that version was to click the Continue button…
Dear LD,
If your experiment requires precise control over calcium levels, EGTA should be preferred due to its higher selectivity for calcium ions. However, if calcium levels are not critical or can be adjusted accordingly, EDTA may be a suitable alternative…
Dirty, damaged, or blocked interface cones drastically impact the sensitivity and background of your ICP-MS system. Small/gradual changes in the vacuum level of the interface region is an indicator of cone maintenance. Learn about how to clean and condition…
Learn about how to inspect the torch, bonnet, shield plate, and RF Coil, as well as torch cleaning and handling recommendations for Agilent ICP-MS systems.
Preventative and regular maintenance are crucial in avoiding ignition issues and plasma instability…
Hello clockhar ,
The calibration table is stored in only one sample in the batch. This is why you keep seeing the same accuracy since this is stored in the peak table.
Unfortunately, it would be very difficult to come up with a Report Builder binding…
Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...
Turn On the GC/MS Interface and Oven Using OpenLab CDS
Multiple Results
This Information Applies To: Agilent GC/MS instruments controlled by OpenLab CDS software
Issue
Turning on the GC/MS interface heater and Oven using OpenLab CDS software.
Steps to Follow
From the Home tab, click Method > Instrument Setup...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900)
Issue
The signal monitor function in MassHunter can help with troubleshooting low sensitivity, carry over, contamination, or high background. It can also be used to optimize...
This Information Applies To: Agilent UV detectors (Variable Wavelength Detectors, Multiple Wavelength Detectors, and Diode Array Detectors)
Issue
Checking accumulated hours on the UV lamp.
Steps to Follow
There are four ways to check the accumulated...
This Information Applies To: Agilent 7700/7800/7850/7900/8800/8900 ICP-MS
Issue:
Poor internal standard (ISTD) mixing can cause high relative standard deviation (RSD).
The recommendations in this article are applicable if:
It takes a long...