Hello,
I am not entirely clear on what you are doing as well. Below is an example of how I would do a % recovery from an existing standard injection in the result set. The calculation would pull the theoretical value (Compund_CalibrationAmount) from…
Hi JONHY , thanks for your question.
I’ve used an online tool to translate your post. English is the official language of the Agilent Community, and the platform does not support translating a post from local language to English. You can view pages…
Hello,
I think there are other posts where I go over this in more detail. If you want to do a recovery or check calculation for more than one compound and it is not a reinjection of a standard level or the standards are not in the results set, the…
Hello,
Yes, that will not work. You need to test the length of the name as I said in the previous response. See the example below the unknowns have a low value of 1.56.
if(LEN(Compound_Name)>0, getconstant(“Relative response factor”),0.98)
…
UV-Vis spectroscopy is a well-established technique in many laboratories. For decades, laboratories have adapted to pain points associated with UV-Vis workflows such as daily instrument warm-up, yearly lamp replacement, and slow and cumbersome temperature…
Timmas You are running 7890A GC/5975 MS/ E.02.02 SP2 ? --- That version of MSD Chemstation was released November 2013 on Windows XP Professionals with SP3. The KBR error/fix you reference is from a document that does not support MSD Chemstation E.02.02…
Thanks Linh and Martin! first of all, it was not enabled in the instrument configuration. After the reconfiguration with intelligent reporting, I can see editing option! Also that course was very useful to me! Thanks a lot both!
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...
Turn On the GC/MS Interface and Oven Using OpenLab CDS
Multiple Results
This Information Applies To: Agilent GC/MS instruments controlled by OpenLab CDS software
Issue
Turning on the GC/MS interface heater and Oven using OpenLab CDS software.
Steps to Follow
From the Home tab, click Method > Instrument Setup...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900)
Issue
The signal monitor function in MassHunter can help with troubleshooting low sensitivity, carry over, contamination, or high background. It can also be used to optimize...
This Information Applies To: Agilent UV detectors (Variable Wavelength Detectors, Multiple Wavelength Detectors, and Diode Array Detectors)
Issue
Checking accumulated hours on the UV lamp.
Steps to Follow
There are four ways to check the accumulated...
This Information Applies To: Agilent 7700/7800/7850/7900/8800/8900 ICP-MS
Issue:
Poor internal standard (ISTD) mixing can cause high relative standard deviation (RSD).
The recommendations in this article are applicable if:
It takes a long...