Hello,
You turned the value back into a number by dividing by10 outside the formatnumber statement. I would just place the entire statement in a Val() function and then format the column as 1 decimal place.
Marty
=Val( If ( Signal_Name like…
Hello staceylouie ,
I apologize for the delayed response.
The error you are seeing was a known issue in that revision due to no structure match being found for the selected compound. The workaround for that version was to click the Continue button…
Dear LD,
If your experiment requires precise control over calcium levels, EGTA should be preferred due to its higher selectivity for calcium ions. However, if calcium levels are not critical or can be adjusted accordingly, EDTA may be a suitable alternative…
Dirty, damaged, or blocked interface cones drastically impact the sensitivity and background of your ICP-MS system. Small/gradual changes in the vacuum level of the interface region is an indicator of cone maintenance. Learn about how to clean and condition…
Learn about how to inspect the torch, bonnet, shield plate, and RF Coil, as well as torch cleaning and handling recommendations for Agilent ICP-MS systems.
Preventative and regular maintenance are crucial in avoiding ignition issues and plasma instability…
Hello clockhar ,
The calibration table is stored in only one sample in the batch. This is why you keep seeing the same accuracy since this is stored in the peak table.
Unfortunately, it would be very difficult to come up with a Report Builder binding…
Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...