If the HiVac pump is off - the system is not under vacuum to be able to run. The MS source and quad cannot be heated until the system is under vacuum.
The directions on how to vent and pump down the MS are in the Operating manual and also the Troubleshooting…
The graphite must deform to seal. It can only deform one time as there is no spring-back. Install it with the inlet cold and the inlet pressure set to zero psi. I like to put the liner in, then place the seal around it using a gloved hand, then tighten…
I have been working with Thermo Orbitrap Exploris 480.
Which type of Agilent Q-TOF MS could have similar performance compared to the Thermo LC-MS instrument?
Since i retired from the previous company for private reason, I am trying to find another…
Thanks Chris. as you are expected, the "Round Thing" was main cause for this issue. i clean both the sensor and Vaccum Fan. Since it was more than 10 year front panel never been inspected. now it running again normally. Againn.. Thanks for your advice…
Hello srlee ,
This would not be a tested or supported workflow. While GCMS SQ data can be processed, in limited testing it appears that if Profinder see ESI data it assumes it is accurate mass. Even attempting to open up the mass filters to something…
Hi! We have been experiencing issues with the sensitivity of our SpectrAA-50/55 using a nitrous oxide/acetylene flame to quantify vanadium. We have been using this setup fairly consistently to quantify vanadium in solution for ~2 years now and have not…
Hello,
So first of all, if the entries you need are numeric and per compound, I would use a CC constants file. There are ways to create one big constants file for all your compounds and use keys values to pull specific columns by method or other values…
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...