Hi, I have an old 6890 with a jet direct card. We lost power to the instrument and since then it has not been able to connect to the PC. I tried updating the bootp software with the correct mac address and power cycled instrument with the same issue.…
Support and educational resources for the Microplate Centrifuge and Automated Centrifuge Loader .
Automation Solutions Knowledge Base
Microplate-Handling Device Guides
PDF user guides
Support Documents
G5582A Centrifuge Installation Checklist…
-Have you tried a diferent column ? An old column could have retention time issues and peak distortion.. -Have you had any pressure fluctuations during your run ? Try running a Pump leak rate test, to see if the problem is not in the pump-head. -Do a…
On a G1329B autosampler I lose the plastic housing to have access to a valve. Then I forgot to reassemble it and when turn the unit on, the needle went to the top.
Now, I cannot put the plastic housing back, and interferes with the arm.
I…
Hi BJohnson would you post your question in the Chromatography Software Forum for better visibility? It would be good to provide the system information (hardware details, software, i.e. OpenLab CDS and software version).
Cheers,
Kristen
Has anyone received this prompt before? I am currently trying to get a data reviewer set up for Data Analysis. Every time we try to load the method for the specific method run it prompts this message and will not load the method needed.
Error Loading…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...