Can you import a compound list from excel to Optimizer in MH12.1? Inside the software, I do not see where to add the position of each compound in the autosampler.
Hello mtmail00
You can configure HPLC from Tool Tab--> Settings--> Hardware--> Sample Instroduction
In Sample introduction you can select " Agilent 1200 LC", after this , auto config pop up appears to type the HPLC IP
Thanks
Regards
Hello! Good morning
Instrument: GCMSMS 7890B (G3445B)
Acquisition Software: MassHunter Workstation GC/MS Data Acquisition Version 10.0 Service Release 1, Build 10.0.384.1
Since last week we've been experiencing one of our instruments randomly stopping…
If it's just over the weekend, I would turn the flame off but keep some flow through the columns. Best to keep the inlet at a minimum of 5 psig and 20 mL/min flow. There are some suggestions in the 8890 Operation manual also: Operation Manual (agilent…
Thank you very much for your reply
Regarding the software error, a complete software reset is usually performed when starting the analysis routine, however, according to your instructions, it was done again, but the error continues.
When the error…
This potential electronics problem is beyond the scope of this forum. The best thing to do is to contact your local Agilent service and start the process of an onsite service call.
Turbomolecular pumps do not have any maintenance procedures. They typically run forever and then don't start back up again after being stopped. Has the problem continued to happen?
The only rough pumps supported by Agilent that should be plugged into the QQQ systems are the Agilent IDP-10 and the Edwards RV-5. Those are the only tested and supported pumps and the only ones used for Agilent service calls. If the MS40-S has the same…
This Information Applies To: 2200/4200/4250 TapeStation systems, TapeStation D1000 ScreenTape assay, TapeStation High Sensitivity D1000 ScreenTape assay, TapeStation analysis software
Issue:
A sharp peak appears at the lower end of the NGS library...
This Information Applies To: Agilent Variable Wavelength Detector G1314x and G7114A/B modules.
Issue
As UV deuterium lamps ages, the light intensity decreases, the sensitivity of detection may deteriorate. Replace the lamp when the intensity test...
This Information Applies To: Agilent 6850, 6890, 7820, 7890, 8850, 8860, 8890, Intuvo 9000 GC Systems with a Thermal Conductivity Detector (TCD)
Issue
The TCD temperature, column (carrier), makeup, and reference flow rates need to be optimized to...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...