Hey Ryan, try the following. Normally, the valve command failed is coming as a result of the position not found. Overtightened screws are a typical result if you have done maintenance before (happened to me the first time...). Tighten the screws each…
Good Evening, I realize this is a bizzare question but basically what we have is a Dean Switch GCMS system and we use cut windows to determine when the best time is to switch from column 1 (inlet to switch to 3rd column - vent) to column 2 (inlet column…
I think that, with this version of the software, there are configuration files stored in the "instrument number folder", e.g. C:\Chem32\n I was going to suggest that you try to delete/rename the config.reg file, having closed all instances of Chemstation…
Hello,
We have an agilent 6545. Today when we are doing a mass calibration check, the masses of the negative tune ions seems to be shifted (For example 1633.9988 is now showing 1639.2109 and so on for the other ions) and mass calibration check seems…
Hi, I am using Agilent 7820A GC-FID with EZChrom Elite v3.3.2. software. After the completion of each sequence, I would like to automatically generate a .text file along .dat file. So far, after the sequence has ended, I process the sequence and then…
Hi, There are so many open questions, that i would ask you to run thorugh the "Troubleshooting Tool". It´s an guided pdf, which helps to identify the problem. The last performance report looks quite well, also the torch axis and the em tuning run without…
Instrument: 7890 GC modified for gas injection with a 10-port valco valve. It's dual SS inlet, dual detector FID/TCD.
I have installed some components into the AUX bracket, two heating components into AUX 1 and AUX 2, and a valve actuator in V1. Valve…
As long as you do not see any issues in your measurements, you can keep using the EM, until your new EM has arrived. At some point the Pulse HV will reach ~1800 V and the Analog HV will reach ~ 3300 V (if you are lucky). After that you will have to replace…
Actually, you have to be sure that it's detector problem or not.
And if still problem persist and after changing lamps intensity test, wavelength test failed again then you have to call to your local agilent support to check electronics and optics etc…
Thank you James, The software that we have, runs in a very old HP computer with Windows 2000 PRO. The equipment´s software only runs in this computer and it has had many fails lately. For it reason, we would like to buy an updated software that it can…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...