Thank you for the reply, I will have a go at it tomorrow. So essentially I just need to change one of my internal standard compounds to a normal compound, and use that as a single point calibration? It just seemed logical that every internal standard…
Hi
I am trying to install the G7201D version of ICP MassHunter on a 1909 Windows 10 laptop.
It goes through the initial process and then errors with a code of 0xe0434352.
Some additional research implies this is a .Net error but a repair install…
In an official Service Note we say "According to our lamp manufacturers there is no shelf life for LC detector deuterium (D2) lamps. Our logistic centers (LC) try to ship lamps from stock before they reach 12 months age. We see the lamps lasting for more…
When you run startup, does it use the Standard Tune or User Tune? In the new D rev of software (5.X) you can go to Startup/Startup Configuration and just above the Hardware settings table select Configure ignition sequence. For C rev (4.X) click the narrow…
What version of Windows do is it running? Go to the cell next to the logo (Type here to search) and enter winver and select the run app. At top it should say Windows 10, at this time only MassHunter 5.2 is Win11 compatible. 2 lines below Windows 10 will…
I have Open Lab CDS Chemstation Edition for GC systems and 7890A with FID. I get in vial concentration of an analyte in a sample from calibration curve as ppm. Need to generate an Intelligent report, I get concentration in sample (with Sample weight,…
Good Afternoon,
I'm developing a processing method using Mass Hunter Quant. 10.2 for ethanol (quantitate) and other related volatiles (ID only). The instrument setup is a single column that splits to two detectors FID and MS (FID for quant purposes…
I am using Agilent 8890. I am trying to set the standard for my GC-FID, I am injecting 5mL of methane gas standard with a gas-tight syringe through a switching valve which is set up to the left of my GC. However, I am getting different peaks and areas…
I have a MicroGC 990. Seemingly out of no where, the following error has popped up after hitting Control -> Single Run on a method we've been using for months:
Failed to submit "D:\ .... path name .... (GMT -04-00).seq" for acquisition.
Please resubmit…
Hello Guys, I am using Agilent 7890a GC with an FID detector. I using this GC in online mode to analyze reactor exit gases. I am currently studying the dehydrogenation of Methylcyclohexane over Pt catalyst. Recently I noticed that the FID response is…
This Information Applies To: 1100, 1200 and 1260 Infinity I and 1260 Infinity II LC Pumps (Excluding preparative pumps with electromagnetic purge valve (EMPV): G1361A. Not applicable to any of the 1290 Infinity II modules with automatic purge valve: G4220X...
This Information Applies To: Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules
Issue:
Removing and re-installing Visible and UV lamps in Agilent 1260 Infinity G1315x DAD or G1365x MWD Modules.
Both the visible and UV lamps are consumable...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pumps.
Issue:
Removal of the pump head from the pump metering drive for maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Module.
Steps...
This Information Applies To: All Agilent 1260 Infinity Binary, Quaternary, or Isocratic Pumps without the Seal Wash Option installed.
Issue:
Worn pump seals can shed small particles that can cause blockages and pressure issues downstream of the...
This Information Applies To: Agilent G7167x Multisampler modules
Issue:
Required when:
The needle seat is visibly damaged, blocked, or is leaking.
Leaks or blockages in the Vialsampler are observed, especially between the needle and needle...
This Information Applies To: Agilent 1260 Isocratic (G1310B) Quaternary (G1311B) Pumps.
Issue
Required when:
The inlet valve is defective.
The pressure or leak test in Lab Advisor suggests the inlet valve may require replacement.
A large...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
Required when:
The outlet valve is defective or leaking.
The pressure or leak test in Lab Advisor suggests the outlet valve may require replacement...
This Information Applies To: Agilent 1260 Isocratic (G1310B) quaternary (G1311B) pump modules
Issue:
The seal wear in procedure is important as it acts to "bed-in" the seals to ensure a leak free and pressure-tight pump head.
Required when:...
This Information Applies To: Agilent G7167A/B Infinity II Multisamplers
Issue:
The Agilent Multisampler autoreferencing procedure uses predefined positions on the base plate and the sample hotel to calibrate the positioning of the needle parkstation...
This Information Applies To: Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump Modules
Issue:
Reinstallation of the pump head on the pump metering drive during maintenance on an Agilent 1260 Infinity Binary, Quaternary or Isocratic Pump...