No, the flows on the two columns downstream of the switch have to be equal. They are feed by the same pressure source, so since MSD is under vacuum and the FID is ambient, the column connected to the MSD has to have more restriction, to keep the flows…
I'm trying to create a report with a column which calculates the percentage of all integrated peaks above a specific threshold. I have created a report parameter to format the number of significant digits, this is a request of some of our clients. At…
I’m sorry for the delayed reply to your message. Do you still need assistance with this? If you do, please take into consideration the notes below. However, if the issue was resolved, could you please share what the resolution was?
From what I understand…
Before first use: Soak in 100ppm sodium calibration standard for 24 hours to condition the probe With use (submersion in the liquids under test) the response time will become slow and it might be difficult to calibrate. If this occurs the probe needs…
Disconnect the sample probe from the valve and start the leak and restriction test. If it passes this step, it means that there is some restriction in the sample probe, enough to cause that part of the test to fail. Try a brand new probe. If it fails…
Seems then to indicate something in the flow path when including the mixer and damper. First, make sure that you do an elasticity calibration because you have changed important parts in the flow path. Then re-run the pump leak rate test with the mixer…
Hi! Recently we baught GC 8890 with tandem detector fid-scd(detector for sulfor detection 8355). In this case limit of detection of sulfur compaunds is very high (ppm level). We need to meet more low limits of detection of sulfur compounds. Can we dismount…
Hello experts!! I have 6460 LCMSMS system. It unfortunately failed in tuning even in brand new tuning solution. Auto tune repeatedly failed in peak width adjustment in MS1. What could be the problems and possible answers? Cleaning is done up to ion transfer…
Thanks for the response Matthais. The issue actually is that autotune sometimes fails to match EPA compliance criteria, and so it becomes necessary to manually tweak settings. I get that Agilent doesn't want lab techs carelessly messing around with quadrupole…
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
The following procedure is to learn how to use the tools in the Compound Information window to view chromatograms and spectra for your data.
Steps to follow...
This Information Applies To: Agilent MassHunter Quantitative Analysis Software
Issue
Batch Table can be configured with many different data columns. This article uses an existing demonstration batch with method and analyzed data files to view different...
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...