Hi All,
I have an Agilent 7700 ICP-MS running MassHunter 4.6. Interesting issue - the instrument tunes just fine but when I go to run a sample, the data acquisition never stops; it continues well past the time it should have taken including rinse program…
Thank you very much for your quick attention. I take advice to use Labadvisor, however, the host computer is a windows 7 system and the built-in net framework is NE3.5, but LabAdvisor downloaded from Agilent site needs Net Framework version 4.7.2 , which…
I am new to GC. I am trying to make a calibration table for a set of fatty acid standards using Agilent 8860 (GC-FID)
After the derivitization step, analysis of the resulting methyl esters shows only the solvent peak. Usually a very high solvent peak…
Hello,
Does anyone know were the signal data for the live signal displayed in the online signal window is stored and/or how to access it in Chemstation Rev.B.04.03[16]? I would like to write a macro to run in the scheduler to periodically grab a live…
This is absolutely the wrong column. Ammonia and H2S need apolar thick films to be separated and no specialized Free-Fatty-Acid-Phase (FFAP). A CP-Volamines column would do (CP7448) . Ammonia elutes just after CO2 and before water, H2S after water at…
First off, it is not the barcode reading that causes the vial leaking, but my best guess is that the barcode reading introduces a variable time, that then can cause a scheduling conflict. This scheduling conflict is then not handled, and the 7697A is…
Hi All,
We have a 5977 MSD which came up with two errors following a site power outage:
"Source Heater Error: Timeout - temperature fails to increase under full power." "Analyser Heater Error: Timeout - temperature fails to increase under full power…
Hi everyone I have a strange issue to report. We are using a 6890GC with FID and TCD that was upgraded many years ago to give use LAN communication rather than GPIB. It works great even though it is over 20 years old. Just prior to Christmas we installed…
We have a GC-MA7890B with an FID detector and I are observing spikes in the baseline after we made a couple of changes.
We installed guard columns with unions on inlet and detector side, added a 2nd gas cylinder and required tubing, cleaned the FID…
For the GC-6890 FID detector issues you're experiencing, here's a simplified approach to troubleshoot the errors:
Gas Supplies:
Make sure all gas supplies (utility, makeup, hydrogen) are on.
Check that the pressure…
This Information Applies To: Agilent MassHunter Qualitative Analysis software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Navigator View.
Steps to follow
Note : Use the demonstration data...
This Information Applies To: All versions of Agilent MassHunter Qualitative Analysis Software , and Agilent MassHunter Quantitative Analysis version B08.00 and up
Issue
Calculation of signal-to-noise in MassHunter is performed using the same parameters...
This Information Applies To: Agilent GC/MS MassHunter Data Acquisition Software
Issue
Preparing and running a sample is essential for data acquisition. The steps below detail how to run a single sample using an Automatic Liquid Sampler (ALS) on...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software version 10.0
Issue
Introduction to MassHunter Qualitative Analysis for Agilent GC/MS – Compound View.
Steps to follow
Note : Use the demonstration data files...
This Information Applies To: Agilent MassHunter qualitative analysis software
Content:
MassHunter can be configured to label TIC chromatographic peaks with the best match compound name from an MS library search.
Steps to follow:
On the top...
This Information Applies To: Agilent MassHunter GC/MS Data Acquisition (Rev. 10.0 and below)
Issue
Users running MassHunter GC/MS Data Acquisition with Microsoft Windows 10, may encounter warning messages about insufficient memory in the PC when...
This Information Applies To: Agilent MassHunter Qualitative Analysis Software, Revision 7 and up
Issue
This article shows the procedure to change the number of decimal places in the Mass Spectrum Preview and MS Spectrum Results windows of the MassHunter...
This Information Applies To: Agilent OpenLab CDS ver. 2.4 or earlier.
Issue:
If the PC name on a system with OpenLab 2.4 or earlier revisions needs to be changed post installation of the software. This must be done in the right way or the instrument...
This Information Applies To: Agilent OpenLab CDS Software (ver 2.x).
Issue:
This article will give instructions on how to submit a single sample run in the OpenLab CDS Software.
Steps to follow:
Launch the acquisition software through the...
This Information Applies To: Agilent OpenLab CDS products
Issue:
Every computer running Agilent OpenLab CDS Software requires a unique software license for continuous operation. Failure to install a valid license will cause the instrument control...