Ah, and I think the issue has to do with that I have 2 autosamplers, and 3 columns (MS at back, and 2 different FID columns at front using a 2way splitter). So the MS signal is in the subsequent folder, the FID1 signal is in the correct folder, and FID2…
The boxes of standards should have shipped with a Certificate of Analysis enclosed. If you go to Agilent.com, you can search on the part number. A number of the hits are CofAs from different batches. part 5080-8858 CofA Lot CF-4631W.pdf (agilent.com)…
Dear team,
I'm running 8890 GC-FID using back injector and front Detector FID. When, we uploaded sequence table, there's message appearing that sequence table rear injection isn't detected. Can anyone help to advise what to do with that?
Thanks…
Hello!
It would be very good to get step by step instruction and definition of each row on Splitter calculator and other calculators to configure our system.
The system uses SCD and FID detectors.
Target is to get ratio 3:1 between SCD and FID for…
My knowledge of GCs is extremely limited. Currently we analyze for n-pentane only. The program was already set-up when I started working here.
Yes, an FID is present
1. Sampling vessel type unknown at this time.
2. I am expecting the range to be…
I have the flex metal G3188-27501 ferrules. when it comes to the Inlet, the ferrules fit alright and I can tighten them onto the column. When it comes to the FID port, the ferrule is too long and I can't screw in the column to the outlet. If I really…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
While removing a column from an Agilent mass spec 5977B the column broke off and I can't figure out how to remove it. I'm using MassHunter version 10.1.64.1 (12/15/2021) but not actually using the mass spec but only the FID on the back. If I start a sequence…
How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...