Hello !
I interesting gc8890 and gc7890.
In datasheet the gc 7890 writing about posible instal 3 detector maximum, but in datasheet gc 8890 writing about posible 4 detector. I never see 4 detectors are installed simultaneously on one chromatograph…
Hi abtisam, The main reason for this problem you didn't select detector signals. when we don't selecAdd t signal detector we never see baseline chromatogram,to solve this problem from online plot for FID signal Click on change than from Edit signal plot…
Hi wcody, thank you for the reply! It is Windows 10 Pro 64-bit. These 6890 FIDs are new to the lab, Windows 10 pro was what the technicians had installed on the computers when we received them.
The test can be done with or without flow cell. Like I said, the last test didn't look awfully bad to me (remember, a failed test in LabAdvisor doesn't necessarily indicate a real problem or even hardware failure).
Check your environmental conditions…
There is currently no available solution for working with MassHunter data. If your GC has an FID in addition to a mass spec, you could use OpenLab GC ChemStation to acquire the FID signal data. Then addon G2887BA could be used to analyze the ChemStation…
First of all, thank you for posting publicly, I had not noticed this interface feature of MassHunter Quant, it looks very useful.
Were you able to get it working in 11.1?
If you're allowed to share your "IScriptable" folder, I would be very interested…
ISH, that is a very good question. Yes, you can. However, you have to be mindful of a few things. For the Deans Switch to operate optimally, the downstream pressure need to be the same on both columns downstream of the Deans switch. The MSD operates under…
What are the pros and cons of putting a TCD in series with an MS? I know that it's possible to put a TCD and FID in series but I want MS data, not FID data. I tried teeing off the column between the MS and TCD but all the samples keep going to the MS…
James, Thanks again. Actually, at first we had "EPC or detector error” and we tried to clean the detector but with no change. Once the GC says “Ignite, ignite” the error pops out. We tried second module (the refurbished) and at first we were receiving…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...
This Information Applies To: Agilent CI Source
Issue:
During normal operation of the GC/MS, the CI ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or routine replacement of consumable parts (filament and...
This Information Applies To: Agilent OpenLab CDS
Issue
This article will explain how to add a sequence summary report line to a sequence, in Agilent OpenLab CDS, as well as how to configure it so it matches your reporting needs.
Background ...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS ChemStation, OpenLab CDS EZChrom.
Issue
Process for creating a desktop shortcut for your instruments, with OpenLab software, to enable quick access to your acquisition window.
Background...
This Information Applies To: Agilent LC Systems
Issue
Agilent modules will go into an error status (red status light) when an error condition specific to that module occurs. For example, metering home failed will be specific for the autosampler...
This Information Applies To: Agilent Analytical LC Autosamplers
Issue
To increase the maximum injection volume of an autosampler, there are two ways to do it. While both will provide larger injection volumes, there are advantages and disadvantages...
How to Recover a SubscribeNet Password
Multiple Results
This Information Applies To: Agilent Software products with SubscribeNet license.
Issue
Resolutions for password recovery use if you have: lost your password, been locked out of the account, or you don't know if you have an account with SubscribeNet...
This Information Applies To: Agilent OpenLab CDS, OpenLab CDS EZChrom
Issue
Steps to create a Data Analysis shortcut for one or more of your Projects defined in the OpenLab Control Panel .
Steps to Follow
Open the Control Panel of your...