Hi everyone. There are some doubts that I would like to clarify because we're experiencing some drift and sensitivity problems and it may help.
We've already cleaned the cones, lenses and sample introduction system, including the torch.
1) There is…
The peak to the left in the Lithium window is Li6. This is from internal standard solution. Li6 abundance is typically very low and should not be larger than the Li7 peak. When you run start the plasma, is the internal standard (ISTD) line in a nitric…
Hi kalle-h,
Has the method worked well for you in the past? Any changes recently like column trims? Sometimes small pieces of column can get caught inside the modulator fittings and impede flow, which has negative effects on our data.
If your peaks…
Hello brandon.mendoza.ardena ,
It would be hard to tell, not seeing it or hearing it in person. But a good start would be to make sure there is nothing in the carousel that might cause that (broken vials, caps, or various other debris).
Could also…
Hello Durjoy123 ,
The logic board for 7890A+ does not have the same part number as the 7890A. I wouldn't hazard a guess as whether it will "work" or not. It seems like it does in your case.
But as a general rule I would stick to the board part number…
Check out our new article titled Mastering Pressure Management in GPC/SEC Systems , which has been published in the April issue of the Column . The authors are Dr. Daniela Held and Dr. Michael Krämer .
Hi Biyi ! Is it that the QTOF appears online the Agilent MassHunter Workstation Data Acquisition software? When I power cycle my 6545 XT Q-TOF, I push the power button the Q-TOF and wait maybe 30 seconds. We try not to go more than a minute of being off…
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue:
The Flame Ionization Detector (FID) jet could become clogged with ferrule material, column bleed, or heavy molecular analytes. The clogged jet will affect...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different high concentration, split analysis techniques including:
General use liners
Auto inject, general use
Auto...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different splitless trace analysis techniques including:
General use liners
Pressure, temperature, volume (PTV)
Hot...
This Information Applies To: Agilent 6890, 7890, 7820, 8890 and 8860 GC Systems with Split/Splitless (S/SL) inlet
Issue
Replacement of the Gold Seal is required as part of inlet maintenance. Replacement is required when the performance of the inlet...
This Information Applies To: Agilent GC Systems with Micro-ECD.
Issue
The Wipe Test is an annual test that performed by end user of the micro-ECD (Micro Electron Capture Detector or uECD) to help ensure radioactive safety when using the detector...
This Information Applies To: Agilent GC Systems with thermal conductivity detector (TCD)
Issue
Baking the thermal conductivity detector (TCD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items...
This Information Applies To: Agilent GC Systems with flame ionization detector (FID)
Issue
Baking out the flame ionization detector at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items required...
This Information Applies To: Micro Electron Capture Detector (uECD)
Issue
Baking the micro electron capture detector (µECD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Warning ...
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue
This article will describe how an operator can configure the makeup gas on both the instrument keypad and the software driver (Method Editor).
Background...
This Information Applies To: Agilent HPLC systems
Issue
The presence of ghost peaks can be a symptom of a system contamination issue, caused by accumulation of sample and/or foreign substances in the flow path. It is critical for high sensitivity...