I have a 5890 GC running ASTM D2887, simulated distillation. It is equipped with a FID and recently we noticed the FID won't light. Flows are good and gases are good. Looking at the setpoint/actual reading, it states it is at the correct temperature …
I completed the inlet leak test and it passed and I also completed the FID jet restriction test and it passed. Yet, when I compare scans on the 8890 the peaks shift more compared to the same injections on my 6890. Does anyone have any thought on this…
I appreciate your answering my post!
I tried launching in the Control Panel, with the correct project selected. I also tried to launch MH12.1 using a desktop shortcut made for that project.
I'm sorry, I'm not sure what ESW/FW refers to, could you…
Adding to this post,
I've tried creating a virtual instrument to check if is a problem with the hplc, Aquisition still is not opening for the virtual device.
the acquisition logo stops at initializing modules, turns black and then crashes.
Hello DET ,
Sorry for the late response on this.
What sort of spiking do you see usually? What is the output of the FID, in pA?
Are you using any UPS systems, or are the GCs plugged directly into the wall?
Our customer got an error, "Failed to connect to an IPC Port: The system cannot find the file specified." from MassHunter.
Do you know any cause of this message? There was no record of this message in the diagnostic log files.
during installation of NEW FLD Detector it started to show error Excitation Motor didn't find its position then gives error Excitation motor has failed and last error it still showing up is Exciation endcoder index failed to calculate so what do you think…
I am getting an error on our Agilent 1290/6420 LC-MS/MS. I start a run and the first injection is successful, then when it goes to the second injection, it errors and says "failed switching to main pass" and shuts down. From my reading, this is a failure…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...