Hello MikeL ,
Just wanted to post what we discussed during your call with the support center so if anyone else sees a similar problem they will have some things to try.
There can be issues with copying and pasting fairly large amounts of information…
How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
I'm running a GC(7890A) / MS(5975C) with MassHunter Acquisition software. I automate much of my data analysis in Python by exporting the GC signal (FID) to .csv, and then exporting the MS signal using 'Export 3-D Data...' in MSD Productivity Chemstation…
i had faced this troubleshooting before
it is probably a software problem.
first close masshunter and double click ( remove masshunter process)
open the soft again and try to create another method with same parameters it should work
also try to…
Recently, we connected the column (CP7429) to TCD and FID using a Y splitter. However, there is no signal response on both TCD and FID after manually injection of the calibration gas (containing H2, CO, CH4, C2H4, C2H6 in CO2). The carrier gas is Ar.…
When performing the Eukariote Total RNA test on the same chip we had some samples with very degraded RNA and one sample with what seems like good quality RNA but the software failed to give a RIN value for that sample. Is there a way to still measure…
Dear Colleagues, apologizing for frequently wondering but I first faced this problem. GC produces a signal without turning on the FID Detector!? Please look at the attached photo. After turning on the detector and then conditioning the column while the…
Hello AGILENT family,
i have a few questions on the analysis of Pb in blood samples.
am failing to get the right concentrations of the QC sample 8ppb instead it’s reading 0.08 ppb and at the same time it’s also showing overange (0.08o) even when my…
For many FID methods, 10-20 Hz data rate is sufficient unless you're doing a fast method of some sort. You need enough data points to define the peak correctly and not get any spectral tilt. Typically 15-20 points across the peak is enough.
This Information Applies To: Agilent ICP-MS MassHunter Workstation 4.6 or below, and ICP-MS MassHunter Workstation 5.1 and above.
Issue
Guide for identifying the current software version your Agilent ICP-MS system is using, to see if any updates...
This Information Applies To: Agilent OpenLab ChemStation, Agilent OpenLab EZChrom, Agilent OpenLab CDS.
Issue
When users of OpenLab CDS forget their passwords, another user with the right privileges will reset their password, however, sometimes...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to temperature can cause the plasma to shut off or disable plasma ignition. While a warning message will still allow the plasma to light...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
How to view meters in ICP-MS MassHunter Software, or change what meters are selected?
Background
ICP-MS MassHunter allows up to five meters to be displayed at...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to replace the oil mist filter in the MS40+ or MS40-S?
Background
The oil mist filter in the MS40+ or MS40-S should be replaced yearly.
Warning :
...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to check the DS 402 foreline pump to determine if the pump needs maintenance.
Background
The oil cleanliness and oil level in the DS 402 foreline pump should be checked...
This Information Applies To: Agilent ICP-MS systems (7700, 7800, 7850, 7900, 8800, 8900)
Issue
After shutting down and restarting the ICP-MS, sometimes the communication between ICP-MS and PC does not automatically reconnect. It may be necessary...
This Information Applies To: Agilent ICP-MS (7700/7800/8800)
Issue
How to replace the Foreline Pump Oil Mist Filter in the DS 402 foreline pump.
Background
The oil mist filter element should be replaced yearly , or when the level of oil in...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil Mist Filter and Odor Element in the E2M18 or E2M18F?
Background
The oil mist filter and odor element should be replaced yearly, or if the...
This Information Applies To: Agilent ICP-MS (7500/7700/8800)
Issue
How to replace the Forline Pump Oil in the E2M18 or E2M18F?
Background
The E2M18 oil should be replaced at least every three months or when the oil color indicates it needs...