Thank you for the help so far. I was able to solve the problem on my results table by using the "left outer join" function.
However, the report will not print the individual peak chromatograms for the target ion or qualifiers if there was no peak detected…
Hi,
1. It is not normal, that you have to purge the cell gas lines every time
2. Ou should perform at least following "Tests" during Plasma ignition: Torch Axis - EM - Resolution/Axis. But a performance report every day would be nice (and therefore…
Hi everyone I have a strange issue to report. We are using a 6890GC with FID and TCD that was upgraded many years ago to give use LAN communication rather than GPIB. It works great even though it is over 20 years old. Just prior to Christmas we installed…
Varian 710 oes, nebulization is ok, fog in the chamber is omogeneous, tubing, nebulizer, torch, cone cleaned and alligned.
Work fine till 2 weeks ago, after i've experienced this: fail to execute wavelenght calibration end torch allign, No response…
Hello Everyone,
I am using 7820A GC coupled with 5977B Mass Spec. After use I close the He tank and later on I get 2 messages - 'Front inlet flow shutdown' and 'Front inlet pressure shutdown'. I restarted the software but it fails to load any GC method…
I am building a report for some GC-FID data from a GC-MS/FID instrument. I have managed to build a report that contains the chromatogram and the table of peaks. I can scale the X-axis to the scale i need but I have been unable to scale the y-axis to show…
I am using OpenLab Chemstation C.01.10 on an 8890 with dual FIDs. I was trained on HP's version of Chemstation that reported both detector quant amounts in one row for precision purposes. It made it 10x easier to review data and confirm sample concentrations…
Hello, we are setting up a seahorse assay for a immunology master class. We want to measure the glycolytic rate in human PBMCs or purified human CD4 T cells activated vs non activated. We fail to see any difference. Has anyone done this kind of assay…
Hi Juliana
Yes, most likely the capacitors and/or the RF Tube. However, you can try to reduce the run power to 1.1Kw in the default ignition table. You may then be able to run for a few weeks with this reduced power level. You will need to reduce the…
We have a Duo 2.5 foreline pump that was replaced in June of this year (2023). The previous Duo 2.5 installed had a sudden catastrophic leak, thus the replacement in June. The oil was filled up halfway and I set a marker with tape to monitor the level…
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...
This Information Applies To: Agilent 7693A, 7650A, and 7683 Series automated liquid samplers
Issue
GC software or GC LED display shows ALS Failure code 245: Autosampler front tower plunger error or ALS Failure Code 945: Auto injector back tower...
This Information Applies To: TapeStation ScreenTapes and reagents
Issue
Using the search tool on Agilent.com to locate the declarations of conformity (DOC) for Agilent ScreenTapes and Test-Tapes, certificates of conformity (COC) for TapeStation...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The Automatic Liquid Sampler (ALS) system calibration process aligns the sample tray with the injector turret position to enable vial transfers without incident.
Calibration...