1 uL is injected for PAH.
We do change the liner often and are using the one from all the app notes (with glass wool). We haven't tried a dimpled but do use a dimpled with the PBDE method.
After doing a bunch of troubleshooting over the last few…
I'd like to bump this thread up to the top because in our lab we have had the same problem, and our amazing IT guy was able to solve it!
It turned out that on the PC where the Data Analysis (same version as olabanalyst ) was faulty, it had been installed…
Hi everyone. There are some doubts that I would like to clarify because we're experiencing some drift and sensitivity problems and it may help.
We've already cleaned the cones, lenses and sample introduction system, including the torch.
1) There is…
The peak to the left in the Lithium window is Li6. This is from internal standard solution. Li6 abundance is typically very low and should not be larger than the Li7 peak. When you run start the plasma, is the internal standard (ISTD) line in a nitric…
Hi kalle-h,
Has the method worked well for you in the past? Any changes recently like column trims? Sometimes small pieces of column can get caught inside the modulator fittings and impede flow, which has negative effects on our data.
If your peaks…
Hello brandon.mendoza.ardena ,
It would be hard to tell, not seeing it or hearing it in person. But a good start would be to make sure there is nothing in the carousel that might cause that (broken vials, caps, or various other debris).
Could also…
Hello Durjoy123 ,
The logic board for 7890A+ does not have the same part number as the 7890A. I wouldn't hazard a guess as whether it will "work" or not. It seems like it does in your case.
But as a general rule I would stick to the board part number…
Check out our new article titled Mastering Pressure Management in GPC/SEC Systems , which has been published in the April issue of the Column . The authors are Dr. Daniela Held and Dr. Michael Krämer .
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...