Hello igorvlad
I’m sorry for the delayed reply to your message. Do you still need assistance with this? If you do, please take into consideration the notes below. However, if the issue was resolved, could you please share what the resolution was?…
Thank you for your advice. Unfortunally not only EM test failed but several others as well. we tried to run it last,first, and even not to run it at all
The GC Calculators and Method Translation Software (MTS) is available for download from Agilent.com . The package includes:
The Vapor Volume Calculator . It can be used to determine the expansion volume of a GC sample solvent at a given inlet temperature…
Hi, Here's a screenshot of the system suit, there is no blank subtraction The analyst said he has used the same processing method for a different run with no issues the only difference being that for those runs the MS setting was the same time as the…
The basic tools I would recommend to have for GC maintenance:
Ceramic column cutter
1/4" wrench (column nuts)
7/16" wrench (gas fittings at back of GC)
1/2" wrench (replace gold seal on S/SL inlet)
Torx 20 driver (removing FID collector assembly…
Agilent GC 7890A, FID, Split Liner. I'm setting up the column to do Hexane injection testing. It was set up this way previously but the program had been deleted and the column removed before I started here. Front Detector/Column which is below baseline…
Hello and Help!
My GC-FID's inlet pressure stays at 0.7 psi and does not reach the setpoint of 10 psi. Makeup gas reaches the 25 psi setting. Liner and septa are fine. I unscrewed the inlet column nut and placed my finger at the bottom of the inlet…
When you say that there are no signs of a leak, have you run a pump leak rate test using Agilent Lab Advisor? If not, I would suggest testing this. If you're unlucky enough for your peak to elute just at the point when the outlet ball valve fails to close…
Hello,
My laboratory runs a multilevel calibration with internal standards on a headspace-GC-FID. Our sequence is set up to replace each level of the curve after each calibrator is analyzed and then calculate the concentration of the analyte with the…
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...
This Information Applies To: All Agilent 6000 Series LC/MS Systems without a gate valve for ion capillary installation/removal. For instructions for removing an ion capillary on LC/MS instruments with a gate valve installed, please click here
Issue...
This Information Applies To: Agilent 6000 series LC/MS instruments
Issue:
Cleaning the ion transfer capillary as part of regular maintenance or as part of troubleshooting when a loss of sensitivity in the instrument occurs.
Steps to follow ...
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Efficient electrospray ionization (ESI) in your LC/MS ion source requires a properly adjusted nebulizer needle in good condition. The nebulizer needle is a consumable item in...